CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums

Search Results

Register Blogs Community New Posts Updated Threads Search

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: Sniper
Forum: OpenFOAM Pre-Processing December 4, 2013, 16:05
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, thanks for the reply, I tried what...

Hi Bruno,

thanks for the reply, I tried what is mentioned in the directory, but was not able to get it work. Should I run the commands mentioned in the web page in the OpenFOAM/user/run directory...
Forum: OpenFOAM Pre-Processing November 28, 2013, 11:49
Replies: 31
Views: 12,787
Posted By Sniper
Open channel Flow with VOF

Hi

I am planning to model a simple open channel flow with VOF for free surface. I am using the interFoam solver based on the water channel tutorial. I want to specify a desired water depth at the...
Forum: OpenFOAM Pre-Processing August 28, 2013, 11:22
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, Thanks for the link, it was very...

Hi Bruno,

Thanks for the link, it was very helpful.

For my problem, I am trying to run with a mapped inlet boundary and trying to map the flow parameters at the outlet on the inlet. But when I...
Forum: OpenFOAM Pre-Processing August 25, 2013, 18:25
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, Thanks for your suggestions, it...

Hi Bruno,

Thanks for your suggestions, it helped me a lot. I am right now trying to use the command foamToTecplot360, it does not seem to work. I get the following error

foamToTecplot360:...
Forum: OpenFOAM Pre-Processing August 23, 2013, 13:59
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, Thanks for your help. Could...

Hi Bruno,

Thanks for your help.

Could you point me to any tutorial we I can give velocity profile at my inlet.

Thanks & Regards,

Vimal.
Forum: OpenFOAM Pre-Processing August 22, 2013, 15:11
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, Giving the velocity as the initial...

Hi Bruno,

Giving the velocity as the initial condition does work with simpleFoam solver. The entire domain is set to that velocity value and there is no variation.

I am trying to setup the case...
Forum: OpenFOAM Pre-Processing August 22, 2013, 12:36
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, The reason I asked about that...

Hi Bruno,

The reason I asked about that tutorial was, I thought I can make make my inlet and outlet as cyclic and can give the velocity as an initial condition. Do you think this would work?
...
Forum: OpenFOAM Pre-Processing August 22, 2013, 09:59
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, I have not been able to still...

Hi Bruno,

I have not been able to still setup the case. Could you let me know why does a simpleFoam a steady state solver has a initial conditions file in motorBike tutorial.

Regards,

Vimal
Forum: OpenFOAM Pre-Processing August 18, 2013, 21:47
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, Thanks for your reply. I will...

Hi Bruno,

Thanks for your reply.

I will run the case using the mapped BC and compare with the StarCCM results and keep the community posted.

Is there a way to port the data from openFOAM to...
Forum: OpenFOAM Pre-Processing August 18, 2013, 18:52
Replies: 31
Views: 12,787
Posted By Sniper
Hi Bruno, Thanks for your reply... I was...

Hi Bruno,

Thanks for your reply... I was looking at different tutorials for a solution to this problem. I came across a tutorial with a boundary condition called mapped.

Would it work in case...
Forum: OpenFOAM Pre-Processing August 18, 2013, 15:15
Replies: 31
Views: 12,787
Posted By Sniper
simple open channel flow, the inlet and outlet are periodic

Hi Bruno,

Thank you very much for the information... I was able to convert it and just as you predicted the resultant mesh was not very good.

As a result, I am trying to run the case in...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 09:59.

Contact Us - CFD Online - Privacy Statement - Top