Search Results

Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: saisanthoshm88

Forum: ANSYS Meshing & Geometry

March 26, 2011, 02:53

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Many Thanks for all the worthy replies Simon

Many Thanks for all the worthy replies Simon

Forum: ANSYS Meshing & Geometry

March 24, 2011, 23:14

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Thanks for the reply Simon , can you please...

Thanks for the reply Simon , can you please explain about the inverted distribution with the split prisms option in ICEM and then were you referring to the split face ( blocking) defect ( the work...

Forum: ANSYS Meshing & Geometry

March 20, 2011, 02:06

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Hi Simon, The problem with the prisms was...

Hi Simon, The problem with the prisms was resolved when the prism layers were redistributed with an initial height of 0.1

Forum: ANSYS Meshing & Geometry

March 9, 2011, 12:54

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Thanks for the help Simon I didn't get any...

Thanks for the help Simon

I didn't get any error out of the existence of single edges while using the top down octree method but I had an error while using the bottom up smoothing (Advanced front)...

Forum: ANSYS Meshing & Geometry

March 9, 2011, 07:21

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Well Simon I found that the problem with the...

Well Simon I found that the problem with the error in advance front algorithm can be resolved by fixing the single edges issue in the geometry by using either the Use Local Tolerance (or) Single...

Forum: ANSYS Meshing & Geometry

March 3, 2011, 02:58

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

I used the color by count option for the curves...

I used the color by count option for the curves to figure out the problem but I couldn't infer anything appreciable from that. Can you please help me out by looking into the geometry if you find some...

Forum: ANSYS Meshing & Geometry

March 2, 2011, 02:26

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Help requested

Hi Simon,
In this mean while I tried to build the mesh with Quick Delaunay and Smooth (Advanced Front) so that there can be a better volume transition than the robust octree mesh.

But...

Forum: ANSYS Meshing & Geometry

February 21, 2011, 11:24

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Many Thanks Simon.

Many Thanks Simon.

Forum: ANSYS Meshing & Geometry

February 21, 2011, 07:31

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Thanks for the reply Simon. I’ve tried the...

Thanks for the reply Simon. I’ve tried the approaches suggested but couldn’t get any improvement in the tet-prism mesh.

Cycles of Laplace smoothing were run.

The ortho weight was...

Forum: ANSYS Meshing & Geometry

February 18, 2011, 05:37

Replies: 17

[ICEM] Low quality Tet prism mesh

Views: 10,808

Posted By saisanthoshm88

Low quality Tet prism mesh

I was meshing a tray in a cooking oven. The tray is enclosed in a volume and then meshed. The quality of the Tet prism mesh is too bad.

The following is the URL link for a ppt that contains the...

Showing results 1 to 10 of 10

Forum Jump

All times are GMT -4. The time now is 17:00.