CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums

Search Results

Register Blogs Members List Search Today's Posts Mark Forums Read

Showing results 1 to 12 of 12
Search took 0.00 seconds.
Search: Posts Made By: -mAx-
Forum: ANSYS Meshing & Geometry October 13, 2010, 02:56
Replies: 25
Views: 5,557
Posted By -mAx-
this is not a tutorial. I only draw it quick in...

this is not a tutorial.
I only draw it quick in gambit
Forum: ANSYS Meshing & Geometry October 12, 2010, 05:06
Replies: 25
Views: 5,557
Posted By -mAx-
which tutorial?

which tutorial?
Forum: ANSYS Meshing & Geometry March 30, 2010, 07:05
Replies: 25
Views: 5,557
Posted By -mAx-
Smoothing and remeshing options only work with...

Smoothing and remeshing options only work with tetra
Forum: ANSYS Meshing & Geometry March 18, 2010, 07:09
Replies: 25
Views: 5,557
Posted By -mAx-
with moving mesh, you don't just only need to...

with moving mesh, you don't just only need to define the moving walls.
You need to create moving zone, deforming surfaces, etc..
check the tutorial about Moving Mesh, it will help you to understand...
Forum: ANSYS Meshing & Geometry March 18, 2010, 06:11
Replies: 25
Views: 5,557
Posted By -mAx-
I mean delete. There should be no cell in the...

I mean delete. There should be no cell in the square. (enable shaded mode an check if the square is empty, like in my picture)
my example is 2d, so gambit recognizes mappable surface and mesh it...
Forum: ANSYS Meshing & Geometry March 18, 2010, 02:16
Replies: 25
Views: 5,557
Posted By -mAx-
I confirm what I said: delete the blue square,...

I confirm what I said: delete the blue square, and set its outter edges as rigid body motion
On the picture you can see that the square is empty.
2626
Forum: ANSYS Meshing & Geometry March 17, 2010, 14:13
Replies: 25
Views: 5,557
Posted By -mAx-
can you post an hand-sketch of your model?

can you post an hand-sketch of your model?
Forum: ANSYS Meshing & Geometry March 17, 2010, 10:47
Replies: 25
Views: 5,557
Posted By -mAx-
why do you want to keep the small volume? Are the...

why do you want to keep the small volume? Are the outter surfaces not enough?
Except if you want to compute conduction in solid, you don't need the solid mesh.
Your mesh should contain a hole,...
Forum: ANSYS Meshing & Geometry March 3, 2010, 10:11
Replies: 25
Views: 5,557
Posted By -mAx-
If the grey brick will move using layering, you...

If the grey brick will move using layering, you have to
check the tutorial "Using Dynamic Mesh"
It is based on layering, and everything is described.
Your issue sounds like your MDM parameters...
Forum: ANSYS Meshing & Geometry March 2, 2010, 09:01
Replies: 25
Views: 5,557
Posted By -mAx-
yes with remeshed option, you need to work with...

yes with remeshed option, you need to work with tetras only.
Layering can also be used, but it depends on your geometry. You can also use sliding mesh + layering
Forum: ANSYS Meshing & Geometry March 2, 2010, 07:59
Replies: 25
Views: 5,557
Posted By -mAx-
post a picture

post a picture
Forum: ANSYS Meshing & Geometry February 23, 2010, 03:26
Replies: 25
Views: 5,557
Posted By -mAx-
*check the warning in the transcript window while...

*check the warning in the transcript window while exporting
*check if you don't have superposed entitis at your inlet
*check in the Boundyry Panel if your inlet is still set (if it is already...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT -4. The time now is 16:19.