Search Results

Showing results 1 to 8 of 8
Search took 0.00 seconds. Search: Posts Made By: tH3f0rC3

Forum: OpenFOAM Meshing & Mesh Conversion

March 15, 2011, 05:24

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

ok, no I have checked, that this isn't the...

ok, no I have checked, that this isn't the mistake.
I will proceed on with checking.

The error message I recieve is the following:...

Forum: OpenFOAM Meshing & Mesh Conversion

March 15, 2011, 04:43

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

I can now specifie my problem: The files...

I can now specifie my problem:

The files exported from ANSA are not recognized as cpp-files and OpenFoam want files in cpp-format.

I think a problem could be that my ANSA can only export in...

Forum: OpenFOAM Meshing & Mesh Conversion

March 15, 2011, 02:30

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

Ok. When I blockMesh in the tutorials openFoam...

Ok.
When I blockMesh in the tutorials openFoam creates exactly the same files like ANSA outputs. So far so good.
But the fils created from ANSA seemed not to be exactly that what OpenFoam needs to...

Forum: OpenFOAM Meshing & Mesh Conversion

March 14, 2011, 15:38

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

Ok, these are exactly the files which where...

Ok, these are exactly the files which where created inmy case, too.
But I think I have read in the OpenFoam User Guide, that OpenFoam needs a blockmesh-file.
But thanks for your answer, i will...

Forum: OpenFOAM Meshing & Mesh Conversion

March 14, 2011, 11:18

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

I have found the pipe_bend Tutorial. It describes...

I have found the pipe_bend Tutorial. It describes that procedure very good. Some of your collegues has suggested to do so in another thread.

But I have exported my data for a little test-modell...

Forum: OpenFOAM Meshing & Mesh Conversion

March 13, 2011, 06:37

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

Hi, does someone know a tutorial, which...

Hi,

does someone know a tutorial, which describes the procedure to put in the data from ANSA (geometry, boundary conditions,...) to ParaFoam?

Regards,
tH3f0rC3

Forum: OpenFOAM Meshing & Mesh Conversion

March 12, 2011, 03:49

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

Hi, I still have read through the list of...

Hi,

I still have read through the list of solvers, but can I use a solver from the group "Heat transfer and buoyancy-driven flows", if I have no buoyancy-driven flows?
I have a flow caused by a...

Forum: OpenFOAM Meshing & Mesh Conversion

March 11, 2011, 02:51

Replies: 10

[Commercial meshers] ANSA to OpenFoam

Views: 5,683

Posted By tH3f0rC3

ANSA to OpenFoam

Dear all,

I want to create a simulation in ANSA, solve it with OpenFoam and ParaView as the Post-Processor.
I want to simulate a flow. Now I have several questions:
- Do I have to be careful...

Showing results 1 to 8 of 8

Forum Jump

All times are GMT -4. The time now is 18:05.