CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > Siemens

Turbulent Jet

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   February 5, 2001, 12:33
Default Turbulent Jet
  #1
Ulf E
Guest
 
Posts: n/a
I am trying to modell a simple axissymmetric turbulent jet (air to air at Re = 11000) at the exit of the jet. But my results look terrible and I believe that it depends on the boundary condition and the size of the domain. I would really appreciate advices in this type of modelling with no "walls". Regards Ulf
  Reply With Quote

Old   February 6, 2001, 07:48
Default Re: Turbulent Jet
  #2
Ahmed Hassaneen
Guest
 
Posts: n/a
I believe you are simulating a confined jet. Could you tell us how terrible are your results to try to find out why it is terrible.
  Reply With Quote

Old   February 6, 2001, 08:12
Default Re: Turbulent Jet
  #3
Ulf E
Guest
 
Posts: n/a
Hi Ahmed The computational domain consist of several recirculation zones!!! I use inlet, pressure and symplane as boundary conditions. I try to model the jet as a steady state problem, but it seems more propely to use a transient-solution. Regards Ulf
  Reply With Quote

Old   February 6, 2001, 08:30
Default Re: Turbulent Jet
  #4
Ahmed Hassaneen
Guest
 
Posts: n/a
Hi Ulf,is your jet impinging somewhere? where is the outlet? what is the Re?
  Reply With Quote

Old   February 7, 2001, 03:19
Default Re: Turbulent Jet
  #5
Ulf E
Guest
 
Posts: n/a
Hi again!

The jet is not impinging and the Re=11000, based on the jet-velocity and the jet nozzle diameter. I seem to find a (good) solution with a transient approach but I donīt understand why I don't get a solution with a steady state approach, Regards Ulf
  Reply With Quote

Old   February 7, 2001, 04:34
Default Re: Turbulent Jet
  #6
Ahmed Hassaneen
Guest
 
Posts: n/a
If it is not impinging somewhere, how do you define the outlet boundary, this could be one of the reasons.
  Reply With Quote

Old   February 7, 2001, 05:25
Default Re: Turbulent Jet
  #7
Ulf E
Guest
 
Posts: n/a
Hi again!! I define my "outlet" boundary as a pressure boundary. And I have to make a sufficient long domain in the axial direction, in order to make sure that the flow is undisturbedly. The domain is 100*Dj in the r-direction and 400*Dj in the axial direction, where Dj is the jet-nozzle diamter.
  Reply With Quote

Old   February 7, 2001, 06:39
Default Re: Turbulent Jet
  #8
Ahmed Hassaneen
Guest
 
Posts: n/a
Ulf, try to make a confinment from two sides (the nozzle plan and the side parallel to the axisymetric) and see if you will reach steady state. I think with your boundary it is too difficult to reach steady state. Also you may try to use less values instead of 100 Dj use 10 Dj and instead of 400 Dj use 40 Dj and see if it makes any difference.
  Reply With Quote

Old   February 12, 2001, 04:19
Default Re: Turbulent Jet
  #9
Carl Fredrik Stein
Guest
 
Posts: n/a
Hi! The pressure field of a normal jet decays as R^-2, where R is the spherical radius (Unconfined jets have spherical, or hemispherical rather than cylindrical symmetry.) Hence, pressure boundary conditions can be used when imposed sufficiently far away. However, it is well known that you do get better results if you use absorbing outflow conditions which ensure that you get the correct mass flow. There are some references in my article in J. Fluids Eng. March 1999, vol 121, pp 102--105, and I know that Cercignani and Moin (independently) have used these conditions subsequently, but I do not know where their results are published. From your name I suspect that you are Swedish, so send me an email (carste@frt.frontec.se) and I will give you my phone number in case you want to discuss the matter any further.

Yours sincerely, Carl Fredrik Stein
  Reply With Quote

Old   February 13, 2001, 09:25
Default Re: Turbulent Jet
  #10
sudeep
Guest
 
Posts: n/a
What is the Mach no?
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Turbulent intensity and turbulent dissipation Phil FLUENT 2 February 14, 2018 06:06
Using different turbulent viscosities for turbulent stress components braennstroem OpenFOAM Running, Solving & CFD 13 October 15, 2010 09:59
lam to turbulent venkatesh FLUENT 0 August 4, 2008 02:31
turbulent jet ramo Main CFD Forum 1 September 4, 2005 08:43
turbulent jet Nasri L Main CFD Forum 0 January 3, 2001 05:56


All times are GMT -4. The time now is 11:09.