Max and min wave height variating in time with 5order stokes waves

lucaoggi · October 22, 2014, 03:20

Hi everybody, I am currently running a simulation of a floating body in 5order stokes waves (1.8s period, 0.3m hight, 10mdepth).

What happens is that max and min wave height oscillates with a low frequency (ca.0.2Hz) resulting in large oscillations (on the same frequency) in the heave response whcih are summing to the supposed heave response due to the wave height/period. I have created my mesh following the suggestions that i found on the Steve forum and refining the free surface area as follow:
X & Y sizes to about 1/80th to 1/100th of the VOF wave wavelength.
Z size to about 1/20th of the wave amplitude.
second order unsteady solver time step relatively to the wavelength division chosen, using the following equation: if the dx chosen was 1/80th, then use (wave period) / (2.4 * 80).

The boundary conditions chosen are
velocity inlet for top, inlet and bottom
pressure outlet for outlet
symmetry for sides

I am having a long domain enough domain to damp my waves and i applied the damping to the pressure outlet boundary My model is 0.25m in diameter and i have and my domain size is 33m (from -8m to +25m)m, 10m, 20m. The model is placed 8m after the inlet.

Any clue about why this is happening?

Thanks in advance!

dai549592484 · October 31, 2014, 07:16

give your result plot plz.

October 22, 2014, 03:20	Max and min wave height variating in time with 5order stokes waves	#1
lucaoggi New Member lucaoggi Join Date: Mar 2012 Posts: 2 Rep Power: 0	Hi everybody, I am currently running a simulation of a floating body in 5order stokes waves (1.8s period, 0.3m hight, 10mdepth). What happens is that max and min wave height oscillates with a low frequency (ca.0.2Hz) resulting in large oscillations (on the same frequency) in the heave response whcih are summing to the supposed heave response due to the wave height/period. I have created my mesh following the suggestions that i found on the Steve forum and refining the free surface area as follow: X & Y sizes to about 1/80th to 1/100th of the VOF wave wavelength. Z size to about 1/20th of the wave amplitude. second order unsteady solver time step relatively to the wavelength division chosen, using the following equation: if the dx chosen was 1/80th, then use (wave period) / (2.4 * 80). The boundary conditions chosen are velocity inlet for top, inlet and bottom pressure outlet for outlet symmetry for sides I am having a long domain enough domain to damp my waves and i applied the damping to the pressure outlet boundary My model is 0.25m in diameter and i have and my domain size is 33m (from -8m to +25m)m, 10m, 20m. The model is placed 8m after the inlet. Any clue about why this is happening? Thanks in advance!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
y+ and u+ values with low-Re RANS turbulence models: utility + testcase	florian_krause	OpenFOAM	114	August 23, 2023 05:37
multiphase turbulance case floating error	harsha_kulkarni	OpenFOAM Running, Solving & CFD	3	February 18, 2016 05:06
Problem of simulating of small droplet with radius of 2mm	liguifan	OpenFOAM Running, Solving & CFD	5	June 3, 2014 02:53
How to write k and epsilon before the abnormal end	xiuying	OpenFOAM Running, Solving & CFD	8	August 27, 2013 15:33
On the damBreak4phaseFine cases	paean	OpenFOAM Running, Solving & CFD	0	November 14, 2008 21:14

October 31, 2014, 07:16		#2
dai549592484 Member David Join Date: Nov 2011 Posts: 39 Rep Power: 14	give your result plot plz.