Flow visualization at overset mesh interface

haizhou0410 · December 22, 2020, 21:04

Hi everyone,

I use star-ccm+ overset mesh method to do flow simulations with motions. I found that the flow e.g. vorticity plot at the overset mesh interface has some problems. It seems that not all unwanted cells are blanked. I use tecplot value blanking and use the "blank entire cells when 'primary value is blanked' "option and blanked the cells when overset cell status equal to 1, -1, -2 which corresponding to inactive, acceptor that is used as donor and acceptor respectively. But it still has problems with the interface which are shown in the picture. Does anyone know what can I do with this? Thank you very much in advance!

profi_star-ccm+ · December 23, 2020, 11:04

I could not find your error. I'm going to study again.

333.png

222.png

111.jpg

haizhou0410 · December 25, 2020, 01:57

You have a nice flow field plot. I can't see any error that appeared in my case. How did you make this happen? Have you tried to plot this in tecplot? Thank you! Btw, nice model.

Quote:

Originally Posted by profi_star-ccm+

I could not find your error. I'm going to study again.

Attachment 81737

Attachment 81738

Attachment 81739

ping · December 27, 2020, 02:32

have you looked at the equivalent scenes in star using its post processing which is designed to automatically deal with the display of overset mesh results?

if they look correct then why go to tecplot anyway- what does it have that star can't do for general p.p.?

December 22, 2020, 21:04	Flow visualization at overset mesh interface	#1
haizhou0410 New Member Jim Join Date: Aug 2019 Posts: 13 Rep Power: 6	Hi everyone, I use star-ccm+ overset mesh method to do flow simulations with motions. I found that the flow e.g. vorticity plot at the overset mesh interface has some problems. It seems that not all unwanted cells are blanked. I use tecplot value blanking and use the "blank entire cells when 'primary value is blanked' "option and blanked the cells when overset cell status equal to 1, -1, -2 which corresponding to inactive, acceptor that is used as donor and acceptor respectively. But it still has problems with the interface which are shown in the picture. Does anyone know what can I do with this? Thank you very much in advance!

December 23, 2020, 11:04		#2
profi_star-ccm+ New Member Aleksandr Join Date: Nov 2020 Location: Russia city Yakutsk Posts: 15 Rep Power: 5	I could not find your error. I'm going to study again. 333.png 222.png 111.jpg Last edited by profi_star-ccm+; December 25, 2020 at 01:39.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
objects oscillate at high speed causing collapse in Dynamic mesh and overset mesh ca	insane	OpenFOAM Running, Solving & CFD	0	May 17, 2020 22:35
Basic Nozzle-Expander Design	karmavatar	CFX	20	March 20, 2016 08:44
[mesh manipulation] Importing Multiple Meshes	thomasnwalshiii	OpenFOAM Meshing & Mesh Conversion	18	December 19, 2015 18:57
Waterwheel shaped turbine inside a pipe simulation problem	mshahed91	CFX	3	January 10, 2015 11:19
How to make a smooth interface for multiphase flow with dynamic mesh?	aegean333	OpenFOAM Programming & Development	0	May 10, 2013 05:34

December 27, 2020, 02:32		#4
ping Senior Member Ping Join Date: Mar 2009 Posts: 556 Rep Power: 20	have you looked at the equivalent scenes in star using its post processing which is designed to automatically deal with the display of overset mesh results? if they look correct then why go to tecplot anyway- what does it have that star can't do for general p.p.?