Design Manager STAR-CCM+ Optimization Study Imported Geometries

ompm · April 14, 2021, 05:31

Hi everyone, I would like to run a position optimization study of wind around buildings. I am planning to study it with design manager in star ccm+ but i am not sure if it is possible.
To put it simple, i have a building of interest with neighboring blocks. I would like to study the optimal placement of the building by rotating it about the z axis at the center of the building. Remeshing and running again by importing new geometries would be extremely tedious. The geometries i am using are always imported as a surface mesh in .stl format. I looked up the internet and most of the tutorial are based on creating new 3D parts inside star ccm. Hence i am exploring the possibility of using design manager to conduct this study. Please assist. Thank you.

SESP · April 15, 2021, 04:44

Hi,

yes, this is possible. You basically need to draw your geometries inside the CAD Modeler, give parameters to the dimensions you want to change so that these can be modified later by the design manager.

ompm · April 15, 2021, 05:04

Hi SESP,

Thanks for the reply! Yes, i am unfortunately stuck at this stage. My geometries may be a little complicated to draw entirely on star ccm+. Hence, i would import it into the 3D-CAD Models. Afterwards i am unsure how to link the parameter to my geometry. Please advise. Thanks!

SESP · April 15, 2021, 05:27

Ok, in that case have a look at the "Replace Part" operation. You can find it under Geometry => Operations. It is for the scenario where several STLs are prepared and stored in a folder and can be parameterized and combined with the Design Manager. From my understanding this could be pretty much what you are looking for.

April 14, 2021, 05:31	Design Manager STAR-CCM+ Optimization Study Imported Geometries	#1
ompm New Member QQ Join Date: Apr 2021 Posts: 2 Rep Power: 0	Hi everyone, I would like to run a position optimization study of wind around buildings. I am planning to study it with design manager in star ccm+ but i am not sure if it is possible. To put it simple, i have a building of interest with neighboring blocks. I would like to study the optimal placement of the building by rotating it about the z axis at the center of the building. Remeshing and running again by importing new geometries would be extremely tedious. The geometries i am using are always imported as a surface mesh in .stl format. I looked up the internet and most of the tutorial are based on creating new 3D parts inside star ccm. Hence i am exploring the possibility of using design manager to conduct this study. Please assist. Thank you.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ANSYS: Design of Experiments and Optimization - Upper and Lower Bounds	mrswordf1sh	ANSYS	0	April 5, 2018 07:33
Need help in solving the warning i get while solving with design optimization after s	Dinesh_Dhande	ANSYS	0	March 14, 2016 01:28
3D design optimization in a rotating frame?	ITA91	SU2 Shape Design	2	May 20, 2015 10:01
Compressor design optimization for efficiency	saisanthoshm88	CFX	0	September 9, 2014 15:11
How to do Design Optimization in Fluent 13.0?	p36288	Fluent UDF and Scheme Programming	1	July 20, 2011 00:37

April 15, 2021, 04:44		#2
SESP New Member Join Date: Mar 2011 Posts: 20 Rep Power: 16	Hi, yes, this is possible. You basically need to draw your geometries inside the CAD Modeler, give parameters to the dimensions you want to change so that these can be modified later by the design manager.

April 15, 2021, 05:04		#3
ompm New Member QQ Join Date: Apr 2021 Posts: 2 Rep Power: 0	Hi SESP, Thanks for the reply! Yes, i am unfortunately stuck at this stage. My geometries may be a little complicated to draw entirely on star ccm+. Hence, i would import it into the 3D-CAD Models. Afterwards i am unsure how to link the parameter to my geometry. Please advise. Thanks!

April 15, 2021, 05:27		#4
SESP New Member Join Date: Mar 2011 Posts: 20 Rep Power: 16	Ok, in that case have a look at the "Replace Part" operation. You can find it under Geometry => Operations. It is for the scenario where several STLs are prepared and stored in a folder and can be parameterized and combined with the Design Manager. From my understanding this could be pretty much what you are looking for.