Export Msh fron ICEM CFD 11 to Star-CD4.06

hamoudi · May 26, 2009, 05:44

Good Morning Everybody,

I have 2D simulation, i made the 2D Hexa Mesh in ICEM-CFD 11 to solve it
in Star-CD 4.06, but when i try to Export this mesh by selecting the solver
Star-CD 4.06 I receive this error Message ***
************************************************** **
Running ANSYS-ICEM CFD 11 Star- CD 4 interface vers11.0.1
Error exit This Interface only supports 3D Mesh
Error in Translation
************************************************** **

Please if someone can help me, I am in a waiting for your response
I have lost a lot of time

Thanck you very Much

xamo · May 28, 2009, 07:19

Hi,
as you can read in the Message, you need a 3D mesh for STAR CD. So extrude the 2D Mesh in ICEM one cell layer and do the export again.

vishyaroon · May 28, 2009, 07:37

What if you export a STAR 3.26 readable mesh, read the mesh in STAR CD 3.26. Then if you create a mdl file, see what happens when you open the mdl file in STAR 4.06.

I not have tried this for 2D geometries, but have had to do something like this where I cannot go directly to STAR 4.06.

I guess that since STAR CD 4.0x was designed to read in CCM meshes, which includes polyhedral meshes, we often run into such problems when dealing with 2D geometries.

murash-v · June 12, 2009, 14:31

Hi. I usually done this by file.CGNS

May 26, 2009, 05:44	Export Msh fron ICEM CFD 11 to Star-CD4.06	#1
hamoudi Member Hamoudi djamel Join Date: Apr 2009 Posts: 50 Rep Power: 15	Good Morning Everybody, I have 2D simulation, i made the 2D Hexa Mesh in ICEM-CFD 11 to solve it in Star-CD 4.06, but when i try to Export this mesh by selecting the solver Star-CD 4.06 I receive this error Message * ********************************************** Running ANSYS-ICEM CFD 11 Star- CD 4 interface vers11.0.1 Error exit This Interface only supports 3D Mesh Error in Translation ************************************************ Please if someone can help me, I am in a waiting for your response I have lost a lot of time Thanck you very Much

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ICEM CFD use for ?	Vu Trinh Tuan	CFX	14	April 11, 2011 18:38
OpenFOAM on MinGW crosscompiler hosted on Linux	allenzhao	OpenFOAM Installation	127	January 30, 2009 19:08
ICEM CFD Modules	Boris	FLUENT	1	March 12, 2004 14:37
switching from build 2 ICEM CFD 4.CFX	bogesz	CFX	4	February 27, 2004 01:31
Which is better to develop in-house CFD code or to buy a available CFD package.	Tareq Al-shaalan	Main CFD Forum	10	June 12, 1999 23:27

May 28, 2009, 07:19		#2
xamo New Member Join Date: Mar 2009 Posts: 20 Rep Power: 16	Hi, as you can read in the Message, you need a 3D mesh for STAR CD. So extrude the 2D Mesh in ICEM one cell layer and do the export again.

May 28, 2009, 07:37		#3
vishyaroon Senior Member Aroon Join Date: Apr 2009 Location: Racine WI Posts: 148 Rep Power: 15	What if you export a STAR 3.26 readable mesh, read the mesh in STAR CD 3.26. Then if you create a mdl file, see what happens when you open the mdl file in STAR 4.06. I not have tried this for 2D geometries, but have had to do something like this where I cannot go directly to STAR 4.06. I guess that since STAR CD 4.0x was designed to read in CCM meshes, which includes polyhedral meshes, we often run into such problems when dealing with 2D geometries.

June 12, 2009, 14:31		#4
murash-v New Member murash-v Join Date: Mar 2009 Posts: 6 Rep Power: 16	Hi. I usually done this by file.CGNS