unable to run the caradonna blade simulation

deeps · May 9, 2014, 08:50

Dear All,

I have been trying to run the config file provided for simulating Caradonna and Tsung blade in the rotating frame of reference. I am using SU2 version 2.7. However, I'm unable to run this case. It blows up after around 30 iterations giving non-physical points and gauss elimination error. The residuals diverge right from the beginning and the CL, CD values are constant at -1000.

1. I'm aware about similar posts earlier. However, they were related to SU2 version 3.0. Has anyone been able to run this case using SU2 2.7 successfully?

2. Also would like to know whether SU2 2.7 would support NS simulation in rotating frame of reference? If yes what is the freestream Mach and Reynolds number to be provided (since this is a hover case freestream M = 0 and so is Re but SU2 won't accept these values). In an earlier post I read that periodic boundary conditions are not fully supported. Could someone please elaborate on this.

Thanks for your help,
Regards,
Deepanshu.

Hennet_m · May 13, 2014, 02:39

Hello,

I have obtained the same problem using version 3.0 of SU2. Using hyperMesh, I have created a mesh without symetricals boundaries (I have modeled two blades) and It works very well!

Hope it helps,

Martin

copeland · May 15, 2014, 15:26

Hello Deepanshu,

Unfortunately, the periodic boundary conditions in SU2 are a little out of date with the rest of the code and right now they don't function properly. Martin's solution of simulating the full geometry is the best solution to the problem if you're looking to get results immediately. We are actively correcting the issues with the periodic boundary conditions and we hope to have the problem resolved & support periodic boundary conditions again within a week or two. Stay tuned for updates!

-Sean

deeps · May 19, 2014, 00:40

Dear Sean and Martin,

Thank you for your suggestions. I'll try simulating the complete pair of blades and will let you know if there are any issues.

Regards,
Deepanshu.

deeps · June 20, 2014, 06:29

Hello Martin,

Could you share your config file? Even after modeling 2 blades I'm not getting a converged solution.

Thanks,
Deepanshu.

economon · June 24, 2014, 20:53

Hi,

Please see the reply here about the new updated C & T case for SU2 V3.2... I think this should clear up some things:

http://www.cfd-online.com/Forums/su2...ade-model.html

T

May 9, 2014, 08:50	unable to run the caradonna blade simulation	#1
deeps New Member Join Date: Nov 2009 Posts: 19 Rep Power: 16	Dear All, I have been trying to run the config file provided for simulating Caradonna and Tsung blade in the rotating frame of reference. I am using SU2 version 2.7. However, I'm unable to run this case. It blows up after around 30 iterations giving non-physical points and gauss elimination error. The residuals diverge right from the beginning and the CL, CD values are constant at -1000. 1. I'm aware about similar posts earlier. However, they were related to SU2 version 3.0. Has anyone been able to run this case using SU2 2.7 successfully? 2. Also would like to know whether SU2 2.7 would support NS simulation in rotating frame of reference? If yes what is the freestream Mach and Reynolds number to be provided (since this is a hover case freestream M = 0 and so is Re but SU2 won't accept these values). In an earlier post I read that periodic boundary conditions are not fully supported. Could someone please elaborate on this. Thanks for your help, Regards, Deepanshu.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Setup of a turbine stator blade conjugate heat transfer simulation	mitra22	CFX	0	February 7, 2014 04:53
Errors running Caradonna (rotating blade) test case	Gaso	SU2	1	June 13, 2013 18:17
Fan Blade Simulation. 2D CFD with FLUENT? CFX?	aerospain	ANSYS	0	December 3, 2010 06:08
helicopter rotor blade simulation	Cesare Ghermandi	CFX	1	June 8, 2004 19:27
Procedure to run unsteady simulation?	STN	Main CFD Forum	2	February 16, 2002 04:37

May 13, 2014, 02:39		#2
Hennet_m New Member Join Date: Oct 2013 Posts: 12 Rep Power: 12	Hello, I have obtained the same problem using version 3.0 of SU2. Using hyperMesh, I have created a mesh without symetricals boundaries (I have modeled two blades) and It works very well! Hope it helps, Martin

May 15, 2014, 15:26		#3
copeland Member Sean R. Copeland Join Date: Jan 2013 Posts: 40 Rep Power: 13	Hello Deepanshu, Unfortunately, the periodic boundary conditions in SU2 are a little out of date with the rest of the code and right now they don't function properly. Martin's solution of simulating the full geometry is the best solution to the problem if you're looking to get results immediately. We are actively correcting the issues with the periodic boundary conditions and we hope to have the problem resolved & support periodic boundary conditions again within a week or two. Stay tuned for updates! -Sean

May 19, 2014, 00:40		#4
deeps New Member Join Date: Nov 2009 Posts: 19 Rep Power: 16	Dear Sean and Martin, Thank you for your suggestions. I'll try simulating the complete pair of blades and will let you know if there are any issues. Regards, Deepanshu.

June 20, 2014, 06:29		#5
deeps New Member Join Date: Nov 2009 Posts: 19 Rep Power: 16	Hello Martin, Could you share your config file? Even after modeling 2 blades I'm not getting a converged solution. Thanks, Deepanshu.

June 24, 2014, 20:53		#6
economon Super Moderator Thomas D. Economon Join Date: Jan 2013 Location: Stanford, CA Posts: 271 Rep Power: 14	Hi, Please see the reply here about the new updated C & T case for SU2 V3.2... I think this should clear up some things: http://www.cfd-online.com/Forums/su2...ade-model.html T