# Fluent FAQ

### From CFD-Wiki

(→What is the role of under-relaxation parameters? What should be the optimum choice of these parameters?) |
|||

Line 25: | Line 25: | ||

==== How do i get better and faster convergence? ==== | ==== How do i get better and faster convergence? ==== | ||

+ | |||

+ | ==== How to merge two mesh files and make one? ==== | ||

+ | To merge two mesh files the suggested utility is tmerge. The syntax of tmerge is simple.<br> | ||

+ | <i>utility tmerge -3d file1 file2 finalfile </i> <br> | ||

+ | To join the two interior faces use: <br> | ||

+ | <i>Grid->Fuse</i> <br> | ||

+ | from the menu with Fluent. | ||

==== What is the role of under-relaxation parameters? What should be the optimum choice of these parameters? ==== | ==== What is the role of under-relaxation parameters? What should be the optimum choice of these parameters? ==== |

## Revision as of 04:57, 22 November 2005

This section is empty. This is just a suggestion on how to structure it. Please feel free to add questions and answers here!

## General purpose codes

### FLUENT

#### What does the floating point error mean? How can I avoid it?

The floating point error has been reported many times and discussed a lot. Here are some of the answers found in the Fluent Forum:

**SOLVER AND ITERATION** -----I think if you set shorter time step, it may be good. Or changing little Under-Relaxiation-Factors, it may be good. In my experience, I set 1/3 Under-Relaxiation-Factors as default.� -----�also lower the values of under relaxation factor and use the coupled implicit solver� -----�Try to change under-relaxation factors and if it is unsteady problem maybe time step is to large.� -----�you can improve the ratio in the solve--control--limits, maybe that can help.� -----�you will need to decrease the Courant number� -----�If you still get the error, initialize the domain with nothing to 'Compute from...' Then click 'init'. Again select the surface from which you want to compute the initial values & iterate. This should work.� -----�Another reason could be a to high courant number - that means, that the steps between two iterations are too large and the change in the results is too large as well (high residuals)�

**GRID PROBLEMS** -----�this error comes when I start scaling grid. in gambit, all my dimension is in mm, when in fluent i convert it in meter using buttone SCALE. after it, when i iterate, about hundred iteration, this error appeared. but when i not scale my drawing to m...and let it be as in gambit..then the iteration is success. -----�hi I think you should check your mesh grid mesh is very high. your problem solve by selection a low mesh.� -----�Your mesh is so heavy that your computers resources are not enough. try to use coarser mesh.�

**BOUNDARY CONDITIONS** -----�In my case I had set a wall boundary condition instead of an axis boundary condition and then FLuent refuses to calculate telling me 'floating point error'.� -----�Your Boudary Conditions do not represent real physis.� -----�wrong boundary condition definition might cause the floating point error. For example setting an internal boundary as interior� -----�Once I had the problem, simulating a 2D chamber with a symmetry BC. I set the symmetry somewhere as �axe symmetric� and the floating point error occur� -----�check the turbulence parameter you set. reduce the turbulence intensity to less that one for first, say 50 iterations.

**USING A UDF** -----�What I mean is really often when people creates UDF they generally forget that for the first iteration some variable can be zero. Therefore if you are divided a number by zero your solver will blow up telling you 'non floating error'. 'non' means 'not a number'. Depending on your UDF this kind of error does not effectively happens at the first iteration. An example, if you are simulated a domain with a stagnant water as initial condition and you are calculated for the first iteration something like 1/Re therefore lets call it BOOM !!! because Re=0 . To find this kind of think there a simple way : reread your UDF.�

**MULTI PROCESSOR ISSUES** -----"I've had similar problems recently with floating point errors on a multi processor simulation. The solution for my problem seems to be to run on a single processor, where it runs fine....?�

#### What is the turbulent viscosity ratio warning and how can I handle?

#### How do i carry out rotating body analysis, eg a rotating sphere or cylinder in flow?

#### How do i get better and faster convergence?

#### How to merge two mesh files and make one?

To merge two mesh files the suggested utility is tmerge. The syntax of tmerge is simple.

*utility tmerge -3d file1 file2 finalfile *

To join the two interior faces use:

*Grid->Fuse*

from the menu with Fluent.

#### What is the role of under-relaxation parameters? What should be the optimum choice of these parameters?

They limit the influence of the previous iteration over the present one. If you choose small values it may prevent oscillations in residuum developing. At the same time the solution may need more time to converge. Keep the default values as they are given in FLUENT. You can decrease them gradually if necessary. Momentum 0.6, pressure 0.1, k 0.4, eps 0.4, mass source 1, viscosity 1.

#### How can I determine the inputs for a porous media or porous jump from flow versus pressure drop data?

#### How do I model heat conduction in a composite wall?

#### What pressures should be specified at inlets and outlets for buoyancy flow problems?

#### Are there any general guidelines on selecting a turbulence model?

#### How can both turbulent and laminar flow be included in one model?

#### How to start a 3D simulation with an compressible medium and temperature changes? What is important to consider

#### What does the abbreviation mean?

CFD = Computational Fluid dynamics FEM = Finite element model UDF = User defined function

### FloWizard

### FIDAP

### POLYFLOW

## Pre-processors

### Gambit

### Gambit Turbo

### TGrid

## Application specific codes

### Icepak

### Airpak

### MixSim

## Educational codes

### FlowLab