# Free-Surface Piercing NACA 0024 Hydrofoil

### From CFD-Wiki

(→References) |
(→References) |
||

Line 25: | Line 25: | ||

[2] Shin Hyung Rhee, Boris P. Makarov, H. Krishinan, Vladimir Ivanov, Assessment of the volume of fluid method for free-surface wave flow, J. Mar. Sci. Technol. 10, pp. 173-180 (2005) | [2] Shin Hyung Rhee, Boris P. Makarov, H. Krishinan, Vladimir Ivanov, Assessment of the volume of fluid method for free-surface wave flow, J. Mar. Sci. Technol. 10, pp. 173-180 (2005) | ||

<br><br> | <br><br> | ||

- | This wiki is based on part of a draft chapter for my TU Delft master's thesis. | + | This wiki is based on part of a draft chapter for my TU Delft master's thesis. Please send your comment to j.h.s.debaar[at]gmail.com |

==Appendix: Experimental Values== | ==Appendix: Experimental Values== |

## Revision as of 13:11, 16 October 2009

## Contents |

## Introduction

This is a validation case for a 3-dimensional Volume of Fluid [Ref. 1] method.

The above picture was taken from Ref. 2. It is a photograph of the experimental setup of the surface piercing foil. It shows a NACA 0024 profile with a chord of 1.2 m, which moves horizontally through the water at a velocity of 1.27 m s-1. This situation corresponds to a Froude number of 0.37 and a Reynold’s number of 1.52E6. When the flow has evolved to a steady situation, the height of the free-surface is measured at a number of positions along the profile.

## Mesh

The mesh for this problem contains 118,800 cells. The solution is time dependent. I monitor the drag coefficient on the profile to see when the problem has reached a stationary solution. I start with a flat free-surface and run the calculations on a coarse mesh. Then I use the solution of the coarse mesh as an initial solution for the fine mesh.

## Results

I compare the calculated wave height along the profile to that from the experiment [Ref. 2]. As can be seen in the figure above, the calculated solution is quite good except at the area around a chord of roughly 0.5 m. This is a well known difficulty and is related seperation, an effect responsible for the development of bubbles – see first figure – in that area.

The accuracy of the solution can be expressed by the Root Mean Squared (RMS) difference between experiment and calculation. For the coarse mesh the RMS = 0.0225, for the fine mesh it reduces to RMS = 0.0206. Since the solution becomes more accurate for the finer mesh, one can be confident that it at least part of the error could dissappear on an even finer mesh.

Finally, it should be noted that the drag coefficient does not reach a steady state but appears to oscillate with a frequency of roughly 1 Hz and an amplitude of roughly 3% of the mean value.

## References

[1] C.W. Hirt, B.D. Nichols, Volume of Fluid (VOF) Method for the Dynamics of Free Boundaries, J. Comp. Phys. 39, pp. 201-225 (1981)

[2] Shin Hyung Rhee, Boris P. Makarov, H. Krishinan, Vladimir Ivanov, Assessment of the volume of fluid method for free-surface wave flow, J. Mar. Sci. Technol. 10, pp. 173-180 (2005)

This wiki is based on part of a draft chapter for my TU Delft master's thesis. Please send your comment to j.h.s.debaar[at]gmail.com

## Appendix: Experimental Values

As found in Ref. 2:

Chord Experiment

0.00 0.082

0.03 0.069

0.06 0.049

0.09 0.029

0.12 0.007

0.15 -0.007

0.18 -0.026

0.21 -0.043

0.24 -0.056

0.27 -0.072

0.30 -0.082

0.33 -0.095

0.36 -0.108

0.39 -0.115

0.42 -0.121

0.45 -0.128

0.48 -0.128

0.51 -0.118

0.54 -0.105

0.57 -0.092

0.60 -0.072

0.63 -0.056

0.66 -0.052

0.69 -0.046

0.72 -0.059

0.75 -0.049

0.78 -0.059

0.81 -0.049

0.84 -0.049

0.87 -0.046

0.90 -0.043

0.93 -0.049

0.96 -0.043

0.99 -0.023

1.02 -0.033

1.05 -0.033

1.08 -0.033

1.11 -0.023

1.14 -0.020

1.17 -0.010

1.20 -0.013