CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Wiki > Spalart-Allmaras model

Spalart-Allmaras model

From CFD-Wiki

(Difference between revisions)
Jump to: navigation, search
(Original model)
(Original model)
Line 49: Line 49:
According to Spalart it is safer to use the following values for the last two constants:
According to Spalart it is safer to use the following values for the last two constants:
:<math>
:<math>
-
\begin{math}
+
\begin{matrix}
C_{t3} &=& 1.2 \\
C_{t3} &=& 1.2 \\
C_{t4} &=& 0.5
C_{t4} &=& 0.5

Revision as of 19:19, 1 September 2006

Spallart-Allmaras model is a one equation model for the turbulent viscosity.

Contents

Original model

The turbulent eddy viscosity is given by


\nu_t = \tilde{\nu} f_{v1}, \quad f_{v1} = \frac{\chi^3}{\chi^3 + C^3_{v1}}, \quad \chi := \frac{\tilde{\nu}}{\nu}

\frac{\partial \tilde{\nu}}{\partial t} + u_j \frac{\partial \tilde{\nu}}{\partial x_j} = C_{b1} [1 - f_{t2}] \tilde{S} \tilde{\nu} + \frac{1}{\sigma} \{ \nabla \cdot [(\nu + \tilde{\nu}) \nabla \tilde{\nu}] + C_{b2} | \nabla \nu |^2 \} - \left[C_{w1} f_w - \frac{C_{b1}}{\kappa^2} f_{t2}\right] \left( \frac{\tilde{\nu}}{d} \right)^2 + f_{t1} \Delta U^2

\tilde{S} \equiv S + \frac{ \tilde{\nu} }{ \kappa^2 d^2 } f_{v2}, \quad f_{v2} = 1 - \frac{\chi}{1 + \chi f_{v1}}

f_w = g \left[ \frac{ 1 + C_{w3}^6 }{ g^6 + C_{w3}^6 } \right]^{1/6}, \quad g = r + C_{w2}(r^6 - r), \quad r \equiv \frac{\tilde{\nu} }{ \tilde{S} \kappa^2 d^2 }

f_{t1} = C_{t1} g_t \exp\left( -C_{t2} \frac{\omega_t^2}{\Delta U^2} [ d^2 + g^2_t d^2_t] \right)

f_{t2} = C_{t3} \exp(-C_{t4} \chi^2)

The constants are


\begin{matrix}
\sigma &=& 2/3\\
C_{b1} &=& 0.1355\\
C_{b2} &=& 0.622\\
\kappa &=& 0.41\\
C_{w1} &=& C_{b1}/\kappa^2 + (1 + C_{b2})/\sigma \\
C_{w2} &=& 0.3 \\
C_{w3} &=& 2 \\
C_{v1} &=& 7.1 \\
C_{t1} &=& 1 \\
C_{t2} &=& 2 \\
C_{t3} &=& 1.1 \\
C_{t4} &=& 2
\end{matrix}

According to Spalart it is safer to use the following values for the last two constants:


\begin{matrix}
C_{t3} &=& 1.2 \\
C_{t4} &=& 0.5
\end{matrix}

Modifications to original model

Model for compressible flows

There are two approaches to adapting the model for compressible flows. In the first approach the turbulent dynamic viscosity is computed from


\mu_t = \rho \tilde{\nu} f_{v1}

where \rho is the local density. The convective terms in the equation for \tilde{\nu} are modified to


\frac{\partial \tilde{\nu}}{\partial t} + \frac{\partial}{\partial x_j} (\tilde{\nu} u_j)= \mbox{RHS}

where the right hand side (RHS) is the same as in the original model.

Boundary conditions

References

  • Spalart, P. R. and Allmaras, S. R. (1992), "A One-Equation Turbulence Model for Aerodynamic Flows", AIAA Paper 92-0439.
My wiki