CFD Online Discussion Forums

CFD Online Discussion Forums (http://www.cfd-online.com/Forums/)
-   ANSYS Meshing & Geometry (http://www.cfd-online.com/Forums/ansys-meshing/)
-   -   [BladeModeler] How to understand the modeling concept in blade modeler (http://www.cfd-online.com/Forums/ansys-meshing/121768-how-understand-modeling-concept-blade-modeler.html)

devesh August 5, 2013 06:41

How to understand the modeling concept in blade modeler
 
I am trying to use Ansys bladegen for generatinng the turbomachinary blade. I am not able to get any tutorials to understand the ways to use it. please suggest?

Far August 5, 2013 07:48

I have some material on it. Send email id.

devesh August 6, 2013 02:59

Thanks
my email id deveshks11@gmail.com.

regards.

ranpreetbhatia September 6, 2013 17:22

Bladegen vs Blademodeler
 
hey guys,

I am pretty confused about both these applications (I mean Bladegen and Blademodeler). Are both of these used for modelling blades? I am trying to obtain 3d models for some blades I have designed.

I have information like chord, axial chord, span, stagger, alpha, beta, etc at 3 locations (thats root, mean and tip). But, I am not sure how to proceed with the blade modelling, all I need is the coordinates for root and tip airfoil (or may be mean as well).

Is there any way, I can get some tutorials on using bladegen or blademodeler to obtain blade profile by provide the above said parameters (thats chord, axial chord, span, stagger, alpha, beta, etc).

Any help or advice would be appreciated.

--
Regards
Ranpreet B

hassan1201 October 3, 2013 07:38

Help please
 
Help me please i can't make flow path around Axial blade and every time Error:confused:


Error: The meridional plane placement is not correct.
Context: ansFClientBMBladeDesign::Execute FlowPath1

my mail: haelsheshtawy@gmail.com

Far October 3, 2013 10:24

are you using blade modeller?

hassan1201 October 3, 2013 10:34

yes i use blade modeler, import point and extrud the blade, and try to make path flow, Plz any help:confused:

hassan1201 October 3, 2013 10:37

Every time this error appears, when make flow path


Error: The meridional plane placement is not correct.
Context: ansFClientBMBladeDesign::Execute FlowPath1

hassan1201 October 3, 2013 10:50

Dear Sijal Ahmed Memon
Please, can you help me?

Far October 3, 2013 11:14

Quote:

Originally Posted by hassan1201 (Post 454893)
yes i use blade modeler, import point and extrud the blade, and try to make path flow, Plz any help:confused:


Do that in turbogrid or design modeller and then use blade editor/blade modeller tool

hassan1201 October 3, 2013 11:44

I had used design modeler for model the blade, after that I used blade editor to make flow path, Can i send the File to you on your email to check out?

hassan1201 October 3, 2013 12:01

1 Attachment(s)
I have airfoil made in design modeler, and i need to make flow path for it.
this figure of my bladehttp://www.cfd-online.com/Forums/att...1&d=1380815954

Far October 3, 2013 13:51

you need hub and shroud surface. After that you need to do some operation, then you will be able to define flow path. You just need few more steps ... :D

hassan1201 October 3, 2013 13:58

I'd made hub, shroud, inlet, and exit lines after that defined it in flow path but
Error massage appears

osmanpekmutlu November 7, 2013 11:04

Quote:

Originally Posted by Far (Post 443879)
I have some material on it. Send email id.

Dear Sijal Ahmed Memon,
Can you send these materials to my email too?
My email id is osmanpekmutlu@gmail.com.
Thanks a lot.

Muratoglu December 10, 2013 15:38

Blade modeler
 
Hi guys! I am new in the blade modeler and try to design a horizontal axis wind/hydro turbine. I think, designing the blade in blade modeler will be better than BladeGen. I need some documentation about blademodeler. My e-mail is: abdmuratoglu@gmail.com

Regards

kd_adem May 10, 2014 04:06

Is it possible to get the material also for me. My e-mail address is: kdadem@gmail.com

Thank you very much Far and Muratoglu.

enzo887 May 19, 2014 14:12

please forward it to me as well:D

androides.gr@gmail.com

ranpreetbhatia May 19, 2014 14:27

Send it to me as well, if you dont mind. :D

Thanks in Advance

My email address is ranpreetbhatia@gmail.com

majidpc May 27, 2014 12:46

And me :D
m_najafpour@aim.com


All times are GMT -4. The time now is 12:47.