F-packing problem

Streamlet · March 13, 2011, 20:39

Hello All
I am simulating a GMO problem(coupled motion with fixed axis) with free surface, the two kinds of error messages listed below always confuse me, I am not sure the meaning of the errors and can do nothing about it. Can anyone help me?
Many thanks.
error in grmsch: 3 3 3
rba =
NaN NaN NaN
NaN NaN NaN
NaN NaN NaN

rbb =
NaN NaN NaN
NaN NaN NaN
NaN NaN NaN

============= mentor tip ===============
persistent f-packing location at t= 0.10573E+03
x= 0.12250E+01, y= 0.00000E+00, z= 0.84250E+01
i= 66, j= 2, k= 68
f= 0.92064E+00
temporarily holding pfpkc constant.
and reducing cfpk by factor of 10
========================================

MuxaB · March 14, 2011, 10:25

The first error requires debugging of the solver and should be reported to the support people.

The second one is only a warning and may not be related to the first one. It is a common occurrence and is not usually a serious problem.

Streamlet · March 14, 2011, 21:11

Thank you very much. But my software is unauthorized right now, so I think I have to tackle this problem by myself

Nicky · April 20, 2011, 04:03

What should I set about the F- packing for die-casting? always use the recommended data?

Nicky · April 29, 2011, 03:41

Hello, everybody,
Can some one tell me what's the meaning of the f-packing coefficient?
I use this software in Die-casting.

March 13, 2011, 20:39	F-packing problem	#1
Streamlet New Member Streamlet Join Date: Mar 2011 Posts: 11 Rep Power: 4	Hello All I am simulating a GMO problem(coupled motion with fixed axis) with free surface, the two kinds of error messages listed below always confuse me, I am not sure the meaning of the errors and can do nothing about it. Can anyone help me? Many thanks. error in grmsch: 3 3 3 rba = NaN NaN NaN NaN NaN NaN NaN NaN NaN rbb = NaN NaN NaN NaN NaN NaN NaN NaN NaN ============= mentor tip =============== persistent f-packing location at t= 0.10573E+03 x= 0.12250E+01, y= 0.00000E+00, z= 0.84250E+01 i= 66, j= 2, k= 68 f= 0.92064E+00 temporarily holding pfpkc constant. and reducing cfpk by factor of 10 ========================================

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
UDF compiling problem	Wouter	Fluent UDF and Scheme Programming	6	June 6, 2012 04:43
Incoherent problem table in hollow-fiber spinning	Gianni	FLUENT	0	April 5, 2008 10:33
natural convection problem for a CHT problem	Se-Hee	CFX	2	June 10, 2007 06:29
Adiabatic and Rotating wall (Convection problem)	ParodDav	CFX	5	April 29, 2007 19:13
Is this problem well posed?	Thomas P. Abraham	Main CFD Forum	5	September 8, 1999 14:52

March 14, 2011, 10:25		#2
MuxaB Senior Member michael barkhudarov Join Date: Mar 2009 Posts: 320 Rep Power: 7	The first error requires debugging of the solver and should be reported to the support people. The second one is only a warning and may not be related to the first one. It is a common occurrence and is not usually a serious problem.

March 14, 2011, 21:11		#3
Streamlet New Member Streamlet Join Date: Mar 2011 Posts: 11 Rep Power: 4	Thank you very much. But my software is unauthorized right now, so I think I have to tackle this problem by myself

April 20, 2011, 04:03		#4
Nicky New Member Join Date: Apr 2011 Location: Suzhou, China Posts: 6 Rep Power: 4	What should I set about the F- packing for die-casting? always use the recommended data?