 |
 |
 |
|
|
|
[Sponsors] | ||||
June 19, 2015, 05:54
|
|
#21 |
|
Member
Martin
Join Date: May 2015
Posts: 30
Rep Power: 11  |
What do you, that I some Howe should run the simulation all over again?
|
|
|
|
|
|
June 19, 2015, 06:04
|
|
#22 |
|
Senior Member
Join Date: Nov 2013
Posts: 1,965
Rep Power: 26 |
If you find out that you did not simulate what you needed to simulate, then yes, you need to do it again.
But the good news is that steady-state is much faster than transient. I don't know why you did transient in the first place... |
|
|
|
|
|
|
June 19, 2015, 06:41
|
|
#23 |
|
Member
Martin
Join Date: May 2015
Posts: 30
Rep Power: 11 |
Its no purpose to run a LES simulation with steady state, off course I am simulating transient. Thank you Pakk but that is not a solution to my problem, it is much easier with UDF if I can get the script right
|
|
|
|
|
|
|
June 19, 2015, 07:32
|
|
#24 |
|
Senior Member
Join Date: Nov 2013
Posts: 1,965
Rep Power: 26 |
If you think steady state LES has no purpose, then don't do it. You are free to spend a lot of computation time to get transient effects into your LES, and later on remove all those transient effects by making the time-average.
[edit: removed unnecessary details] What I am going to say now might make you angry, but be aware that is not my goal. To write code, you need to be accurate and patient, and I don't think you are sufficiently developed in those competences yet. This is all based on the little interaction I had with you in this thread, so I may be completely wrong, but otherwise I would advise you to avoid writing UDFs in the near future. |
|
|
|
|
|
|
June 19, 2015, 07:40
|
|
#25 |
|
Member
Martin
Join Date: May 2015
Posts: 30
Rep Power: 11 |
Yes you are right, No I really tried with the UDF manual, otherwise I could not have done this script even if it may be wrong. Its just that my simulations will take quite some time and I don't have the time to run those simulations again.
But I apologize if I was rude |
|
|
|
|
|
|
June 22, 2015, 03:56
|
|
#26 |
|
Senior Member
Join Date: Nov 2013
Posts: 1,965
Rep Power: 26 |
No problem. I didn't feel you were rude, only inaccurate. Good luck!
|
|
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| write a UDF to give a velocity boundary condition at an interior face | Tharanga | Fluent UDF and Scheme Programming | 19 | August 5, 2018 04:29 |
| WILLING TO PAY/ FREELANCER REQUIRED / small UDF coding force loads over body / 6DOF | acasas | CFD Freelancers | 1 | January 23, 2015 07:26 |
| fluent udf problem: write specific data for every iteration in a file. | nnvoro | Fluent UDF and Scheme Programming | 1 | May 27, 2013 15:26 |
| How to write UDF to achieve phase chang | dunga82 | Fluent UDF and Scheme Programming | 0 | May 6, 2013 08:50 |
| how to write a 3D linear temperature of UDF | venus | FLUENT | 1 | October 28, 2008 02:46 |
Linear Mode
