|
[Sponsors] |
February 20, 2002, 14:26 |
LES idea
|
#1 |
Guest
Posts: n/a
|
Hello to you all,
I am a student who is new to LES and I wish to understand if there are any similarities between LES and RANS? Thank you, Brett. |
|
February 20, 2002, 15:20 |
Re: LES idea
|
#2 |
Guest
Posts: n/a
|
1. LES
LES uses (space) filtered Navier-Stokes and continuity equations. So the solutions are (space) filtered properties, U,V,W,P,etc. 2. RANS Analysis with RANS uses (time) filtered Navier-Stokes and continuity equations. So the solutions are (time) filtered properties, U,V,W,P,etc. Depends on your purpose, you can choose one of those methods. In my case, turbulent flow around bluff body, LES with standard Smagorinsky model gives good results compared to experimental data. The RANS and k-epsilon model estimate reasonably but .... Kim. |
|
February 25, 2002, 04:39 |
Re: LES idea
|
#3 |
Guest
Posts: n/a
|
I appologize for that, but RANS is NOT time filtered NS equations. To get the RANS equations, the NS equations are averaged over realizations. This allows time dependance computations when the time variation are driven by moving mesh or time dependent BCs.
Regards, Sylvain |
|
February 25, 2002, 10:55 |
Re: LES idea
|
#4 |
Guest
Posts: n/a
|
I agree with you. Ensemble averaging is necessary to get RANS equations. However in computational method using RANS, how to get ensemble averaged N-S equation? To make problems simple, time filtering is a kind of Reynolds averaging. This was what I mean.
Thanks Kim. |
|
February 25, 2002, 11:29 |
Re: LES idea
|
#5 |
Guest
Posts: n/a
|
I agree, for steady state turbulence (statistically steady flow), time average values tend to ensemble average values, as an exemple :
Experimentally, for the following channel flow : width = 0.2m; velocity = 10m/s; turbulence intensity = 20%. one needs to average over 8s to get a correct (<1%) mean velocity value. one needs to average over 200s to get a correct (<1%) rms value of the fluctuating velocity. RANS solver give these average values directly. Regards, Sylvain |
|
February 25, 2002, 12:56 |
Re: LES idea
|
#6 |
Guest
Posts: n/a
|
There is numerical error which is growing as the simulation continues. Sometimes, the numerical error can be small due to positive and negative numbers. But anyway, after long time simulation, the accuracy of numerical simulation decreases. So we are careful on the total computation time to get the results from unsteady simulation. (To discuss this problem, the size of grids, the spatial and temporal discretization,etc. are to be touched.)
In my case(LES of flow analysis around 2-dim. square prism, Re=22000), I use periodic condition in spanwise direction with the assumption that the flow is homogeneous in spanwise direction. (But this is not true. My collegue measured the flow field and got some correlation in spanwise direction.) To get velocity and turb. intensity profiles considering reasonable computational time and accuracy, sometimes, I use the average of the whole spanwise direction data. This is a kind of ensemble averaging. (One of my problem is how to compare LES data and the data from RANS equations.) Kim. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
LES basic and simple questions. | dshawul | Main CFD Forum | 0 | October 4, 2010 10:56 |
Turbulence dampening due to magnetic field in LES and RAS | eelcovv | OpenFOAM | 0 | June 8, 2010 11:35 |
LES grid mesh | L3munoz | Main CFD Forum | 0 | April 7, 2010 05:05 |
Differences between a laminar code and a les one | ben | Main CFD Forum | 9 | February 16, 2005 23:40 |
Some Questions about LES. | Bin Li | Main CFD Forum | 2 | February 20, 2004 09:58 |