|
[Sponsors] |
|
April 12, 2010, 04:42 |
|
#1 |
New Member
Begoña
Join Date: Oct 2009
Posts: 28
Rep Power: 16 |
Hi naveen,
I try this, but I have the same mistake, I can't send you the mesh, because my tutor don't like send it. fluent3DMeshToFoam has this mistake: From function fluentMeshToFoam::lexer in file fluent3DMeshToFoam.L at line 747. But fluentMeshToFoam has the next mistake: Reading header: "TGrid 3D 5.0.6" Found unknown block4 Embedded blocks in comment or unknown: ( Found end of section in unknown Found end of section in unknown Dimension of grid: 3 Number of points: 335136 1 (0 1 33c 0number of faces: 2132021 Number of cells: 925081 Found unknown block: (3010 Embedded blocks in comment or unknown: ( Found end of section in unknown: ) Embedded blocks in comment or unknown: ( ?Found end of section in unknown: ?? ?Found end of section in unknown: ?? ???????Embedded blocks in comment or unknown: ? ??Embedded blocks in comment or unknown: Embedded blocks in comment or unknown: ( \?????Embedded blocks in comment or unknown: ? ???Found end of section in unknown: ) Embedded blocks in comment or unknown: ???Found end of section in unknown: ) Embedded blocks in comment or unknown: ????Embedded blocks in comment or unknown: Embedded blocks in comment or unknown: ( \??????Embedded blocks in comment or unknown: Embedded blocks in comment or unknown: ( \??Embedded blocks in comment or unknown: Embedded blocks in comment or unknown \??Embedded blocks in comment or unknown: ? ??Embedded blocks in comment or unknown: ? ??Embedded blocks in comment or unknown: ? ?????????????Found end of section in unknown: " ?@?????Found end of section in unknown: " ?@????@????@?Embedded blocks in comment or unknown: ? ,@???@??Found end of section in unknown: " ?@??@?}Found end of section in unknown:$ ? @????@???@???@?Embedded blocks in comment or unknown: ? ,@?}Found end of section in unknown: $ ? @?Embedded blocks in comment or unknown: ? ,@?Embedded blocks in comment or unknown: ? ,@ ?? ; ??? ; ??? ; ??Embedded blocks in comment or unknown: Embedded blocks in comment or unknown: ( ??Embedded blocks in comment or unknown: Embedded blocks in comment or unknown: ( ???? ; ... The mistake continuous and the terminal don't allow me to introduce more sentences |
|
April 12, 2010, 05:00 |
fluent3DMeshToFoam
|
#2 |
Senior Member
NAVEEN.K.M
Join Date: Mar 2009
Location: Bangalore, Karnataka, india
Posts: 114
Rep Power: 17 |
hi bego,
In the text format what you have got in Tgrid, at the first line change Tgrid into fluent and follow the instructions what i mentioned previously. naveen |
|
April 12, 2010, 05:05 |
|
#3 |
New Member
Begoña
Join Date: Oct 2009
Posts: 28
Rep Power: 16 |
Hi naveen,
thanks, I go to try it |
|
April 19, 2010, 04:04 |
|
#4 |
New Member
Begoña
Join Date: Oct 2009
Posts: 28
Rep Power: 16 |
hello,
I have other problem with fluent file case. When I put in the terminal fluent3DMeshToFoam FILE.cas I have the next mistake: Create time Dimension of grid: 3 Number of cells: 942529 Number of faces: 2186935 Number of points: 347809 --> FOAM Warning : Found unknown block of type: "2012" on line 2960 --> FOAM Warning : Found unknown block of type: "2012" on line 2963 --> FOAM Warning : Found unknown block of type: "2012" on line 2966 --> FOAM Warning : Found unknown block of type: "2058" on line 2969 Do not understand characters: on line 2970 From function fluentMeshToFoam::lexer in file fluent3DMeshToFoam.L at line 747. FOAM exiting With fluentMeshToFoam I have a more big mistake, Can someone help me? Thanks |
|
April 19, 2010, 04:24 |
fluent3DMeshToFoam
|
#5 |
Senior Member
NAVEEN.K.M
Join Date: Mar 2009
Location: Bangalore, Karnataka, india
Posts: 114
Rep Power: 17 |
hi bego,
Can you send me your mesh file. I can convert that into foam format. |
|
April 19, 2010, 04:46 |
|
#6 |
New Member
Begoña
Join Date: Oct 2009
Posts: 28
Rep Power: 16 |
Thanks naveen, but my teacher project don't want that other people has the mesh. She knows another teacher who knows OpenFOAM in Zaragoza, first we try to get out there.
Thank you very much for everything |
|
May 19, 2010, 13:02 |
|
#7 |
Member
Join Date: Nov 2009
Posts: 48
Rep Power: 16 |
Hi Neveen,
I have a problem in converting the fluent3dmesh to OF1.6. I Copied the Msh file into my case directory and type fluentMeshToFoam extension.msh, but i got this error. can you help me? *---------------------------------------------------------------------------*\ | ========= | | | \\ / F ield | OpenFOAM: The Open Source CFD Toolbox | | \\ / O peration | Version: 1.6 | | \\ / A nd | Web: www.OpenFOAM.org | | \\/ M anipulation | | \*---------------------------------------------------------------------------*/ Build : 1.6-53b7f692aa41 Exec : fluentMeshToFoam 8by15by1.75-.05mm.msh Date : May 19 2010 Time : 12:51:56 Host : mehran-desktop PID : 2889 Case : /home/mehran/OpenFOAM/mehran-1.6/run/test nProcs : 1 SigFpe : Enabling floating point exception trapping (FOAM_SIGFPE). // * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * // Create time Dimension of grid: 3 Number of points: 1744596 Reading points number of faces: 5104100 Reading mixed faces Reading mixed faces Reading mixed faces Reading mixed faces Reading mixed faces FINISHED LEXING #0 Foam::error:rintStack(Foam::Ostream&) in "/home/mehran/OpenFOAM/OpenFOAM-1.6/lib/linuxGccDPOpt/libOpenFOAM.so" #1 Foam::sigSegv::sigSegvHandler(int) in "/home/mehran/OpenFOAM/OpenFOAM-1.6/lib/linuxGccDPOpt/libOpenFOAM.so" #2 Uninterpreted: #3 main in "/home/mehran/OpenFOAM/OpenFOAM-1.6/applications/bin/linuxGccDPOpt/fluentMeshToFoam" #4 __libc_start_main in "/lib/tls/i686/cmov/libc.so.6" #5 _start at /usr/src/packages/BUILD/glibc-2.9/csu/../sysdeps/i386/elf/start.S:122 Segmentation fault Thanks, Mehran |
|
November 30, 2010, 06:12 |
view the new mesh
|
#8 |
Member
Join Date: Oct 2010
Location: Stuttgart
Posts: 35
Rep Power: 15 |
hello!
one stupid question (newbie): i've just converted my .msh file into an ASCII format file for OpenFoam with the command "fluent3DMeshToFoam". everything fine. but now i would like to view this converted mesh via paraFoam and i don't know what to do. i have no blockMeshDict file so i cannot use blockMesh.... could someone please help me? thanks |
|
November 30, 2010, 23:03 |
fluent3DMeshToFoam
|
#9 |
Senior Member
NAVEEN.K.M
Join Date: Mar 2009
Location: Bangalore, Karnataka, india
Posts: 114
Rep Power: 17 |
hi grandgo
Just go to the file where your case is located, and type paraFoam and switch off all the vol Field status and accept it..... regards, NAVEEN |
|
December 1, 2010, 10:59 |
|
#10 |
Member
Join Date: Oct 2010
Location: Stuttgart
Posts: 35
Rep Power: 15 |
thanks naveen!
|
|
December 3, 2010, 11:06 |
|
#11 |
Member
Jason G.
Join Date: Sep 2009
Location: St. Louis, IL
Posts: 89
Rep Power: 16 |
||
December 6, 2010, 07:10 |
|
#12 |
Member
Join Date: Oct 2010
Location: Stuttgart
Posts: 35
Rep Power: 15 |
||
April 13, 2011, 15:26 |
converting .msh fluentmeshtofoam
|
#13 | |
New Member
Marta
Join Date: Dec 2010
Posts: 3
Rep Power: 15 |
Hi farghaim,
I am new in OpenFOAM and I´m trying to convert a .msh from FLUENT to OpenFOAM. I´m using OF 1.7.1. I got the same error message you posted in May 2010. Did you find any solution to this problem? I paste you my message in OF hemodynamics@marioc-PowerEdge-R300:~/OpenFOAM/hemodynamics-1.7.1/run/marta/poiseuille_mesh$ fluentMeshToFoam ascii.msh /*---------------------------------------------------------------------------*\ | ========= | | | \\ / F ield | OpenFOAM: The Open Source CFD Toolbox | | \\ / O peration | Version: 1.7.x | | \\ / A nd | Web: www.OpenFOAM.com | | \\/ M anipulation | | \*---------------------------------------------------------------------------*/ Build : 1.7.x-3776603e4c6c Exec : fluentMeshToFoam ascii.msh Date : Apr 11 2011 Time : 22:45:41 Host : marioc-PowerEdge-R300 PID : 13356 Case : /home/hemodynamics/OpenFOAM/hemodynamics-1.7.1/run/marta/poiseuille_mesh nProcs : 1 SigFpe : Enabling floating point exception trapping (FOAM_SIGFPE). // * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * // Create time number of faces: 1643 Number of points: 203 Reading uniform faces Reading points FINISHED LEXING #0 Foam::error:rintStack(Foam::Ostream&) in "/opt/openfoam171/lib/linux64GccDPOpt/libOpenFOAM.so" #1 Foam::sigSegv::sigSegvHandler(int) in "/opt/openfoam171/lib/linux64GccDPOpt/libOpenFOAM.so" #2 in "/lib/libc.so.6" #3 in "/opt/openfoam171/applications/bin/linux64GccDPOpt/fluentMeshToFoam" #4 __libc_start_main in "/lib/libc.so.6" #5 in "/opt/openfoam171/applications/bin/linux64GccDPOpt/fluentMeshToFoam" Violación de segmento hemodynamics@marioc-PowerEdge-R300:~/OpenFOAM/hemodynamics-1.7.1/run/marta/poiseuille_mesh$ Quote:
|
||
April 14, 2011, 03:18 |
|
#14 |
Senior Member
Matthias Voß
Join Date: Mar 2009
Location: Berlin, Germany
Posts: 449
Rep Power: 20 |
Did you also tried fluent3DMeshtoFoam ?
|
|
April 14, 2011, 08:02 |
|
#15 |
New Member
Marta
Join Date: Dec 2010
Posts: 3
Rep Power: 15 |
Thank you Matthias for answering my message.
My mesh is a 2D bifurcation, that is why I am using fluentMeshToFoam. Does fluent3DMeshToFoam work better than fluentMeshToFoam? Do you know what can be the source of my errors? I don´t understand what they mean or how to solve them! Thanks, Marta. |
|
May 29, 2013, 13:08 |
Remember to save mesh as ASCII!
|
#16 |
New Member
Simon
Join Date: Dec 2012
Location: Colorado
Posts: 16
Rep Power: 13 |
I had the same error message as OP. The problem was that the mesh exported by Fluent was in binary format, not ASCII as is required by fluentMeshToFoam. To export as ASCII in ANSYS Meshing, do Tools > Options > Meshing > Export and you will see the option.
|
|
August 16, 2023, 09:04 |
|
#17 | |
New Member
David Kinast
Join Date: Nov 2016
Posts: 15
Rep Power: 9 |
Quote:
I had the same problem. Saving in ASCII-format fixed it! |
||
April 16, 2018, 09:22 |
|
#18 |
New Member
Join Date: Mar 2018
Posts: 1
Rep Power: 0 |
||
October 7, 2019, 04:15 |
Embedded blocks in comment or unkown
|
#19 |
Member
Rosario Arnau
Join Date: Feb 2017
Location: Spain
Posts: 57
Rep Power: 9 |
Hi everyone,
In my case the message "Embedded blocks in comment or unkown" is returned so many times: Code:
@Embedded blocks in comment or unknown:Ҧ \@▒?Embedded blocks in comment or unknown:▒ @ܒ|Embedded blocks in comment or unknown:▒ xterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256colorxterm-256color Thanks, |
|
January 8, 2020, 06:41 |
|
#20 |
Senior Member
Przemek
Join Date: Jun 2011
Posts: 249
Rep Power: 15 |
Hi
I got similar problem. I opened msh file in ICEM, saved as fluent mesh there and now it works.
__________________
best regards pblasiak |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
periodic (cyclic) boundary - fluent3DMeshToFoam | cyln | OpenFOAM | 1 | October 17, 2017 02:59 |
[Commercial meshers] fluent3DMeshToFoam conversion problem | CFDnewbie147 | OpenFOAM Meshing & Mesh Conversion | 14 | March 12, 2014 05:16 |
Possible Bug in pimpleFoam (or createPatch) (or fluent3DMeshToFoam) | cfdonline2mohsen | OpenFOAM | 3 | October 21, 2013 09:28 |
[Commercial meshers] fluentMeshToFoam instead of fluent3DMeshToFoam | sasanghomi | OpenFOAM Meshing & Mesh Conversion | 2 | March 29, 2013 07:58 |
OpenFOAM command from inside MATLAB | sega | OpenFOAM Post-Processing | 18 | September 25, 2012 07:35 |