Search Results

User Name Remember Me Password

Showing results 1 to 13 of 13 Search took 0.00 seconds. Search: Posts Made By: Mohsin

Forum: FLUENT July 15, 2010, 16:16

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin i didn't get your point. Can you please elaborate? i didn't get your point. Can you please elaborate?

Forum: FLUENT July 15, 2010, 12:39

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin oh ok. Thank you very much Chris. So kind of you. oh ok. Thank you very much Chris. So kind of you.

Forum: FLUENT July 15, 2010, 12:05

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Thank you Max for your help. I wanted to... Thank you Max for your help. I wanted to ask one thing about Surface monitors. I did simulation and surface monitors gave flat lines for inlets. Report of "pressure" and Reprt type was "area...

Forum: FLUENT July 15, 2010, 08:19

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Max I didn't understand your quoted sentence? ... Max I didn't understand your quoted sentence? It make only sense if the surface should have a constant pressure? Thank you Max

Forum: FLUENT July 15, 2010, 06:09

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Actually the convergence criteria of residuals... Actually the convergence criteria of residuals and mass flux is acheived but when i look for surface monitors for inlet pressure, I cant get the flat line. what might be the problem? any suggestions?

Forum: FLUENT July 15, 2010, 05:46

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Mr Max thank you for your time. Can you... Mr Max thank you for your time. Can you please explain why I should only check for pressure at the inlet and leave the rest. And whether my target for convergence would only be to make the inlet...

Forum: FLUENT July 15, 2010, 04:22

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Yes Max I got your point. As i gave the pressure... Yes Max I got your point. As i gave the pressure outlet condition at the outlet so it will give me straight line coz i have enforced it to be a constant value. So for outlet I need to check for the...

Forum: FLUENT July 15, 2010, 04:14

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin The inlet boundary condition is "velocity inlet"... The inlet boundary condition is "velocity inlet" the outlet boundary condition is " Pressure outlet". and I gave the constant outlet pressure "0" at a constant operating pressure of 7Mpa.

Forum: FLUENT July 15, 2010, 03:13

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Actually i have 6 outlet surfaces. on 3 outlet... Actually i have 6 outlet surfaces. on 3 outlet surfaces for "pressure" and "report type" as integral I am getting flat line but for the other 3 outlets I am not getting the flat line. Any...

Forum: FLUENT July 15, 2010, 03:01

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Max Thank you. In "Define surface monitor"... Max Thank you. In "Define surface monitor" panel with report type as "integral" under the "surfaces" when i select one surface (example;outlet surface) it gives me flat line but if i select all...

Forum: FLUENT July 15, 2010, 02:02

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Max Thank you for your reply. You mean to... Max Thank you for your reply. You mean to say that I should create a "surface monitor" for my outlet? for example I should create a surface monitor which will report Pressure-static pressure at...

Forum: FLUENT July 15, 2010, 00:59

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Thank you Chris You are right. But how can... Thank you Chris You are right. But how can one know that his solution is not converged until 600 iterations. and now i am getting converged solution after 2000 iterations How can i beleive this...

Forum: FLUENT July 14, 2010, 05:07

Replies: 21 Iterations Querry Views: 4,609 Posted By Mohsin Iterations Querry Hello I ran simulation for 600 iterations and I got converged solution but the results were not accurate/expected. Then i reduced the relaxation factors and did iterations for 2000 until the...

Showing results 1 to 13 of 13

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki