Search Results

User Name Remember Me Password

Showing results 1 to 9 of 9 Search took 0.00 seconds. Search: Posts Made By: linnemann

Forum: OpenFOAM March 3, 2010, 01:53

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi I answered how to open the file in my... Hi I answered how to open the file in my previous post. If you cant figure that out give me a private message with your email and I will send the HDF to you. It is just 50kb larger than the forum...

Forum: OpenFOAM March 2, 2010, 07:01

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hello Here is the same geometry made so it... Hello Here is the same geometry made so it can be hex meshed. Hope you can figure the case structure out. I don't have anymore time to use on this as you just need experience with Salome from...

Forum: OpenFOAM March 2, 2010, 04:49

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi I have no problems creating a mesh using... Hi I have no problems creating a mesh using simple Netgen 3D-2D-1D parameters. I although think you should make a hex mesh on this simple geometry. Ill post an example when I have it.

Forum: OpenFOAM March 2, 2010, 04:42

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi I will look into the case, but I would... Hi I will look into the case, but I would suggest that you upgrade your Salome install. Are you using CAELinux? I would suggest you try and install CentOS and get the Salome version for...

Forum: OpenFOAM March 2, 2010, 03:44

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi disk_1 is just a disk created from the... Hi disk_1 is just a disk created from the new vertex and a vector. in this instance I used the line stradling cylinder_1 as my direction vector. Then I just extruded the disk in the...

Forum: OpenFOAM March 2, 2010, 01:46

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi Its done creating a new vertex from the... Hi Its done creating a new vertex from the middle of a face. I just did it to make a point in the middle of the jet outlet face so I could create a slightly larger cylinder to cut the box with....

Forum: OpenFOAM March 1, 2010, 05:59

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi Unfortunately you cant. It would mean an... Hi Unfortunately you cant. It would mean an internal face which is not possible with OpenFOAM. You have one possibility if you really want a BC at the jet outlet. Use Ggi from...

Forum: OpenFOAM March 1, 2010, 02:20

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi I had a look and it is because you have an... Hi I had a look and it is because you have an internal face where the pipe and the box is fused. I've created a small wall with a diameter slightly larger than the inner diameter of the pipe. ...

Forum: OpenFOAM February 28, 2010, 15:06

Replies: 15 Mesh conversion problem from Salome to openfoam Views: 5,517 Posted By linnemann Hi The ideasUnvToFoam converter have been... Hi The ideasUnvToFoam converter have been updated with better support in the 1.6.x release. Although it looks like you have an internal face in you mesh from the output. You must make sure...

Showing results 1 to 9 of 9

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki