Forum: ANSYS Meshing & Geometry
May 30, 2012, 12:21
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 30, 2012, 12:16
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 30, 2012, 12:15
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 30, 2012, 12:11
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 30, 2012, 11:21
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 17:57
|
Replies: 56
Views: 39,410
Thank you! This helps me a lot. Two questions....
Thank you! This helps me a lot. Two questions. How can you set the courant number for pressure based steady solver? Coupled method is available only for pressure based. Did you use pseudo transient?...
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 16:00
|
Replies: 56
Views: 39,410
Ok with my settings as I wrote here above now...
Ok with my settings as I wrote here above now seems to be ok. I just switched to coupled solver with pseudo transient to speed things up and it's working. When finished I try with enhanced wall...
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 15:54
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 15:49
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 15:45
|
Replies: 56
Views: 39,410
:) Did you have difficulties on convergence? I...
:) Did you have difficulties on convergence? I see that with k-e realizable, all solution methods on second order and default solution controls, continuity residuals slowly diverge. But almost...
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 14:29
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 13:20
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 05:05
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 29, 2012, 04:57
|
Replies: 56
Views: 39,410
Using Orthogonality quality criterion those...
Using Orthogonality quality criterion those elements are above 0.8 but i think that's not the same criterion used by Fluent. What criterion should I check? In icem worst elements are on the lateral...
|
Forum: ANSYS Meshing & Geometry
May 28, 2012, 09:04
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 28, 2012, 07:47
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 28, 2012, 05:36
|
Replies: 56
Views: 39,410
|
Forum: ANSYS Meshing & Geometry
May 27, 2012, 17:33
|
Replies: 56
Views: 39,410
Mesh Quality
Hello,
I'm trying to mesh an ahmed body in ICEM. As you can see in the picture I achieved a fairly satisfactory result. Premesh quality is above 0.5, as well as orthogonal quality once i converted...
|