Search Results

User Name Remember Me Password

Showing results 1 to 6 of 6 Search took 0.00 seconds. Search: Posts Made By: sushant

Forum: OpenFOAM Running, Solving & CFD March 19, 2013, 16:52

Replies: 25 Incorrect introduced mass in sprayFoam? Views: 7,405 Posted By sushant Or you can use 2.2.x, where it should run without... Or you can use 2.2.x, where it should run without any changes needed. See: http://www.openfoam.org/mantisbt/view.php?id=785

Forum: OpenFOAM Running, Solving & CFD February 12, 2013, 10:55

Replies: 25 Incorrect introduced mass in sprayFoam? Views: 7,405 Posted By sushant Hi ris, This solves the issue! That's indeed... Hi ris, This solves the issue! That's indeed what was wrong with my case setup. Thanks a ton, Sushant

Forum: OpenFOAM Running, Solving & CFD February 11, 2013, 11:26

Replies: 25 Incorrect introduced mass in sprayFoam? Views: 7,405 Posted By sushant This is also seen on OpenFOAM 2.0.x (dieselFoam),... This is also seen on OpenFOAM 2.0.x (dieselFoam), integrating the fuel mass inside the closed volume (aachenBomb) much after the spray has all evaporated, falls well short of the specified totalMass:...

Forum: OpenFOAM Running, Solving & CFD February 11, 2013, 11:18

Replies: 25 Incorrect introduced mass in sprayFoam? Views: 7,405 Posted By sushant Hello pushkaraj, Your problem is slightly... Hello pushkaraj, Your problem is slightly different and hopefully easier to solve. You can search around on the forum, there are many posts about the specification of the mass flow rate profile...

Forum: OpenFOAM Running, Solving & CFD December 8, 2012, 13:51

Replies: 25 Incorrect introduced mass in sprayFoam? Views: 7,405 Posted By sushant On 1.6-ext Dear all, On OpenFOAM 1.6-ext dieselFoam does not have this problem, i.e. the injected amount matches the one specified. However, the aachenBomb tutorial in 1.6-ext has 'mass' specified as 2mg....

Forum: OpenFOAM Running, Solving & CFD December 8, 2012, 06:33

Replies: 25 Incorrect introduced mass in sprayFoam? Views: 7,405 Posted By sushant Incorrect introduced mass in sprayFoam? Hi all, When I run any case in sprayFoam (OF 2.1.x) the introduced mass after the end of injection is never equal to the specified totalMass in constant/sprayCloudProperties. This applies also to...

Showing results 1 to 6 of 6

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki