Search Results

User Name Remember Me Password

Showing results 1 to 8 of 8 Search took 0.00 seconds. Search: Posts Made By: m5edr

Forum: ANSYS Meshing & Geometry September 8, 2013, 08:34

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr prism setting... This is my prism setting (image) .... Any suggestion?

Forum: ANSYS Meshing & Geometry September 6, 2013, 16:33

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr Hi Simon yes I did this (Geometry>>... Hi Simon yes I did this (Geometry>> sweep surface), when i made the egde surface longer , the prism is done inside the blade :confused::confused: . If i make the surface longer than the...

Forum: ANSYS Meshing & Geometry September 4, 2013, 13:53

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr thanks simon for reply o.k, what... thanks simon for reply o.k, what should i do for this? yes , i upload an image for Part Mesh setup

Forum: ANSYS Meshing & Geometry September 4, 2013, 06:24

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr also I tried to increase the shell meshing... also I tried to increase the shell meshing elements (increase blade curves nodes) but also the prism fault occurred (the total elements reach to 3 million without volume mesh!)

Forum: ANSYS Meshing & Geometry September 4, 2013, 05:00

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr o.k i did the extruded trialing edge and followed... o.k i did the extruded trialing edge and followed the mentioned steps but the prism fault is the same :confused: i uploaded the new file http://www.4shared.com/rar/bf0GN7Aa/model.html and here is...

Forum: ANSYS Meshing & Geometry September 2, 2013, 16:09

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr Thanks Simon for reply , I appreciated that ... Thanks Simon for reply , I appreciated that I tried that , the min quality was set to 0.00000001, but the prism fault occurred 1- is this will correct the prism fault or only improve...

Forum: ANSYS Meshing & Geometry August 29, 2013, 07:51

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr I also followed the same steps of WingBody... I also followed the same steps of WingBody tutorial that created by @Far http://www.cfd-online.com/Forums/ansys-meshing/101890-wing-body-tutorial-tetra-prism.html but the prism looks like this...

Forum: ANSYS Meshing & Geometry August 27, 2013, 07:44

Replies: 12 [ICEM] Delnauy technique "Bottom-up" problem Views: 2,094 Posted By m5edr Delnauy technique "Bottom-up" problem Hi all, I spent long long time to build a good mesh of my wind turbine blade ( and its enclosure) using octree tetra technique "top down" and after I sent the mesh to Fluent I discovered that the...

Showing results 1 to 8 of 8

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki