Search Results

User Name Remember Me Password

Showing results 1 to 7 of 7 Search took 0.00 seconds. Search: Posts Made By: gschaider

Forum: OpenFOAM Meshing & Mesh Conversion September 3, 2013, 05:47

Replies: 15 [mesh manipulation] How to make a pipe using makeAxialMesh Views: 3,703 Posted By gschaider During regular calculations writePrecision is... During regular calculations writePrecision is irrelevant because data from memory is used. End of discussion

Forum: OpenFOAM Meshing & Mesh Conversion September 3, 2013, 05:12

Replies: 15 [mesh manipulation] How to make a pipe using makeAxialMesh Views: 3,703 Posted By gschaider writePrecision is only relevant if you restart... writePrecision is only relevant if you restart from that data. And if you only need it for postProcessing 6 digits are sufficient (unless you claim to be able to measure the quantity with an accuarcy...

Forum: OpenFOAM Meshing & Mesh Conversion September 2, 2013, 18:25

Replies: 15 [mesh manipulation] How to make a pipe using makeAxialMesh Views: 3,703 Posted By gschaider Because mesh manipulations higher precision... Because mesh manipulations higher precision requirements ("Are these two points the same") Because it wastes diskspace No. Only more accurately WRITTEN data (for calculation it is the same) ...

Forum: OpenFOAM Meshing & Mesh Conversion October 17, 2012, 12:33

Replies: 15 [mesh manipulation] How to make a pipe using makeAxialMesh Views: 3,703 Posted By gschaider OK. You're checking 3 meshes here: - the... OK. You're checking 3 meshes here: - the original planar mesh - the axial mesh (with zero-size faces on the axis) - the collapsed mesh You're interested only in the last one here. Seems like...

Forum: OpenFOAM Meshing & Mesh Conversion August 30, 2012, 16:53

Replies: 15 [mesh manipulation] How to make a pipe using makeAxialMesh Views: 3,703 Posted By gschaider That is hard to tell without seeing the actual... That is hard to tell without seeing the actual failure (of checkMesh I assume)

Forum: OpenFOAM Meshing & Mesh Conversion August 30, 2012, 09:33

Replies: 15 [mesh manipulation] How to make a pipe using makeAxialMesh Views: 3,703 Posted By gschaider @1+2: collapseEdge is only needed if the axis of... @1+2: collapseEdge is only needed if the axis of rotation is part of the geometry. Then a number of faces degenerate to faces of area 0 which is numerically problematic. In the example case in the...

Forum: OpenFOAM Meshing & Mesh Conversion April 27, 2012, 15:31

Replies: 15 [mesh manipulation] How to make a pipe using makeAxialMesh Views: 3,703 Posted By gschaider Well. I think the error message is quite... Well. I think the error message is quite straightforward enough: You're specifying a patch named center as the axis (probably because it is called like that in the example...

Showing results 1 to 7 of 7

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki