|
|
(92 intermediate revisions not shown) |
Line 1: |
Line 1: |
- | ==What is Turbulence?==
| + | {{Introduction to turbulence menu}} |
| | | |
- | Turbulence is that state of fluid motion which is characterized by apparently random and chaotic three-dimensional [[vorticity]]. When turbulence is present, it usually dominates all other flow phenomena and results in increased energy dissipation, mixing, heat transfer, and drag.
| + | __NOTOC__ |
| | | |
- | For a long time scientists were not really sure in which sense turbulence is 'random', but they were pretty sure it was. Like any one who is trained in physics, we believe the flows we see around us must be the solution to some set of equations which govern. (This is after all what mechanics is about- writing equations to describe and predict the world around us) But because of the nature of the turbulence, it wasn't clear whether the equations themselves had some hidden randomness, or just the solutions. And if the latter, was it something the equations did to them, or a consequence of the intial conditions
| + | '''This section is currently undergoing heavy reorganization and editing. Please excuse any errors or unfinished parts. --[[User:Jola|Jola]] 07:01, 21 June 2007 (MDT)''' |
| | | |
- | ===Why Study Turbulence?=== | + | == [[Introduction to turbulence/Nature of turbulence|Nature of turbulence]] == |
| | | |
- | There really are the two reasons for studying turbulence- engineering and physics! And they are not necessarily complementary, atleast in the short run.
| + | * [[Introduction to turbulence/Nature of turbulence#The turbulent world around us|The turbulent world around us]] |
| + | * [[Introduction to turbulence/Nature of turbulence#What is turbulence?|What is turbulence?]] |
| + | * [[Introduction to turbulence/Nature of turbulence#Why study turbulence?|Why study turbulence?]] |
| + | * [[Introduction to turbulence/Nature of turbulence#The cost of our ignorance|The cost of our ignorance]] |
| + | * [[Introduction to turbulence/Nature of turbulence#What do we really know for sure?|What do we really know for sure?]] |
| | | |
- | Certainly a case can be made that we don't know enough about the turbulence to even start to consider engineering problems. To begin with, we always have fewer equations that unknowns in any attempt to predict anything other than the instantaneous motions. This is the famous [[turbulence closure problem]].
| + | == [[Introduction to turbulence/Statistical analysis|Statistical analysis]] == |
| | | |
- | Of course, closure is not a problem when performing a [[Direct numerical simulation (DNS)| direct numerical simulation]] in which we numerically produce the instantaneous motions in a computer using the exact equations governing the fluid. Unfortunately we won't be able to perform such simulations for real engineering problems until at least a few hundred generations of computers have come and gone. And this won't really help us too much, since even when we now perform a DNS simulation of a really simple flow, we are already overwhelmed by the amount of data and its apparent random behaviour. This is because without some kind of theory, we have no criteria for selecting from it in a single lifetime what is important.
| + | * [[Introduction to turbulence/Statistical analysis/Ensemble average|Ensemble average]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Ensemble average#Mean or ensemble average|Mean or ensemble average]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Ensemble average#Fluctuations about the mean|Fluctuations about the mean]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Ensemble average#Higher moments|Higher moments]] |
| + | * [[Introduction to turbulence/Statistical analysis/Probability|Probability]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Probability#Histogram and probability density function|Histogram and probability density function]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Probability#Probability distribution|Probability distribution]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Probability#Gaussian (or normal) distributions|Gaussian (or normal) distributions]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Probability#Skewness and kurtosis|Skewness and kurtosis]] |
| + | * [[Introduction to turbulence/Statistical analysis/Multivariate random variables|Multivariate random variables]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Multivariate random variables#Joint pdfs and joint moments|Joint pdfs and joint moments]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Multivariate random variables#The bi-variate normal (or Gaussian) distribution|The bi-variate normal (or Gaussian) distribution]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Multivariate random variables#Statistical independence and lack of correlation|Statistical independence and lack of correlation]] |
| + | * [[Introduction to turbulence/Statistical analysis/Estimation from a finite number of realizations|Estimation from a finite number of realizations]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Estimation from a finite number of realizations#Estimators for averaged quantities|Estimators for averaged quantities]] |
| + | ** [[Introduction to turbulence/Statistical analysis/Estimation from a finite number of realizations#Bias and convergence of estimators|Bias and convergence of estimators]] |
| + | * [[Introduction to turbulence/Statistical analysis/Generalization to the estimator of any quantity|Generalization to the estimator of any quantity]] |
| | | |
- | The engineer's counter argument to the scientist's lament above is:
| + | == [[Introduction to turbulence/Reynolds averaged equations|Reynolds averaged equations and the turbulence closure problem]] == |
| | | |
- | * airplanes must fly, | + | * [[Introduction to turbulence/Reynolds averaged equations#Equations governing instantaneous fluid motion|Equations governing instantaneous fluid motion]] |
- | * weather must be forecast, | + | * [[Introduction to turbulence/Reynolds averaged equations#Equations for the average velocity|Equations for the average velocity]] |
- | * sewage and water management systems must be built | + | * [[Introduction to turbulence/Reynolds averaged equations#The turbulence problem|The turbulence problem]] |
- | * society needs ever more energy-efficient hardware and gadgets. | + | * [[Introduction to turbulence/Reynolds averaged equations#Origins of turbulence|Origins of turbulence]] |
| + | * [[Introduction to turbulence/Reynolds averaged equations#Importance of non-linearity|Importance of non-linearity]] |
| + | * [[Introduction to turbulence/Reynolds averaged equations#Turbulence closure problem and eddy viscosity|Turbulence closure problem and eddy viscosity]] |
| + | * [[Introduction to turbulence/Reynolds averaged equations#Reynolds stress equations|Reynolds stress equations]] |
| | | |
- | Thus the engineer argues, no matter the inadequate state of our knowledge, '''we have the responsibilty as engineers to do the best we can with what we have'''. Who, considering the needs, could seriously argue with this? Almost incredibly - some physicists do!
| + | == [[Introduction to turbulence/Turbulence kinetic energy|Turbulence kinetic energy]] == |
| + | * [[Introduction to turbulence/Turbulence kinetic energy#Fluctuating kinetic energy|Fluctuating kinetic energy]] |
| + | * [[Introduction to turbulence/Turbulence kinetic energy#Rate of dissipation of the turbulence kinetic energy|Rate of dissipation of the turbulence kinetic energy]] |
| + | * [[Introduction to turbulence/Turbulence kinetic energy#Kinetic energy of the mean motion and production of turbulence|Kinetic energy of the mean motion and production of turbulence]] |
| + | * [[Introduction to turbulence/Turbulence kinetic energy#Transport or divergence terms|Transport or divergence terms]] |
| + | * [[Introduction to turbulence/Turbulence kinetic energy#Intercomponent transfer of energy|Intercomponent transfer of energy]] |
| | | |
- | It seems evident then that there must be at least two levels of assault on turbulence. At one level, the very nature of turbulence must be explored. At the other level, our current state of knowledge- however inadequate it might be- must be stretched to provide engineering solutions to real problems.
| + | == [[Introduction to turbulence/Stationarity and homogeneity|Stationarity and homogeneity]] == |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Processes statistically stationary in time|Processes statistically stationary in time]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Autocorrelation|Autocorrelation]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Autocorrelation coefficient|Autocorrelation coefficient]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Integral scale|Integral scale]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Temporal Taylor microscale|Temporal Taylor microscale]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Time averages of stationary processes|Time averages of stationary processes]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Bias and variability of time estimators|Bias and variability of time estimators]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Random fields of space and time|Random fields of space and time]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Multi-point statistics in homogeneous field|Multi-point statistics in homogeneous field]] |
| + | * [[Introduction to turbulence/Stationarity and homogeneity#Spatial integral and Taylor microscales|Spatial integral and Taylor microscales]] |
| | | |
- | ===The cost of our ignorance=== | + | == [[Introduction to turbulence/Homogeneous turbulence|Homogeneous turbulence]] == |
| | | |
- | It is difficult to place a price tag on the cost of our limited understanding of turbulence, but it requires no imagination at all to realize that it must be enormous. Try to estimate, for example, the aggregate cost to society of our limited turbulence prediction abilities which result in inadequate weather-forecasts alone. Or try to place a value on the increased cost to the consumer need of the designer of virtually every fluid-thermal system-from heat exchangers to hypersonic planes- to depend on empiricism and experimentation, with the resulting need for abundant safety factors and non-optimal performance by all but the crudest measures.Or consider the frustration to engineers and cost to management of the never-ending need for 'code-validation' experiments every time a new class of flows is encounteredor major design change is contemplated. The whole idea of 'codes' in the first place was to be able to evaluate designs wihtout having to do experiments or build prototypes.
| + | * [[Introduction to turbulence/Homogeneous turbulence#A first look at decaying turbulence |A first look at decaying turbulence ]] |
| + | * [[Introduction to turbulence/Homogeneous turbulence#The dissipation equation and turbulence modelling |The dissipation equation and turbulence modelling ]] |
| + | * [[Introduction to turbulence/Homogeneous turbulence#A second look at simple shear flow turbulence |A second look at simple shear flow turbulence ]] |
| | | |
- | ===What do we really know for sure?=== | + | == [[Introduction to turbulence/Free turbulent shear flows|Free turbulent shear flows]] == |
| + | * [[Introduction to turbulence/Free turbulent shear flows#Introduction|Introduction]] |
| + | * [[Introduction to turbulence/Free turbulent shear flows#The averaged equations|The averaged equations]] |
| + | * [[Introduction to turbulence/Free turbulent shear flows#Two-dimensional Turbulent Jets|Two-dimensional Turbulent Jets]] |
| + | * [[Introduction to turbulence/Free turbulent shear flows#Other free shear flows|Other free shear flows]] |
| | | |
- | Turbulence is a subject on which still studies are going on. We really don't know a whole lot for sure about turbulence. And worse, we even disagree about what we think we know! There are indeed some things some researchers think we understand pretty well - like for example the kolmogorov similarity theory for the dissipative scales and the Law of the Wall for wall-bounded flows. These are based on assumptions and logical constructions about how we believe turbulence behaves in the limit of infinite Reynolds number. But even these ideas have never been tested in controlled laboratory experiments in the limits of high Reynolds number, because no one has ever had the large scale facilities required to do so.
| + | == [[Introduction to turbulence/Wall bounded turbulent flows|Wall bounded turbulent flows]] == |
| | | |
- | It seems to be a characteristic of humans(and contrary to popular beleif, scientists and engineers are indeed human) that we tend to accept ideas which have been around a while as fact, instead of just working hypotheses that are still waiting to be tested. One can reasonably argue that the acceptance of most ideas in turbulence is perhaps more due to the time lapsed since they were proposed and found to be in resonable agreement with limited data base, than that they have been subjected to experimental tests over the range of their assumed validity. Thus it might be wise to view most 'established' laws and theories of turbulence as more like religious creeds than matters of fact.
| + | * [[Introduction to turbulence/Wall bounded turbulent flows#Introduction|Introduction]] |
| + | * [[Introduction to turbulence/Wall bounded turbulent flows#Review of laminar boundary layers|Review of laminar boundary layers]] |
| + | * [[Introduction to turbulence/Wall bounded turbulent flows#The "outer" turbulent boundary layer|The "outer" turbulent boundary layer]] |
| + | * [[Introduction to turbulence/Wall bounded turbulent flows#The “inner” turbulent boundary layer|The “inner” turbulent boundary layer]] |
| + | * [[Introduction to turbulence/Wall bounded turbulent flows#The viscous sublayer|The viscous sublayer]] |
| | | |
- | The whole situation is a bit analogous to the old idea that the sun and stars revolved around the earth - it was a fine idea, and even good today for navigational purposes. The only problem was that one day someone (Copernicus, Brahe and Galileo among them) looked up and realized it wasn't true. So it may be with a lot of what we believe today to be true about turbulence - some day you may be the one to look at evidence in a new way and decide that things we thought to be true are wrong.
| |
| | | |
- | ==The Reynolds Averaged Equations and the Turbulence Closure Problem==
| |
| | | |
- | === The Equations Governing the Instantaneous Fluid Motions ===
| + | {{Turbulence credit wkgeorge}} |
| | | |
- | All fluid motions, whether turbulent or not, are governed by the dynamical equations for a fluid. These can be written using Cartesian tensor notation as:
| + | [[Category: Turbulence]] |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \rho\left[\frac{\partial \tilde{u}_i}{\partial t}+\tilde{u}_j\frac{\partial \tilde{u}_i}{\partial x_j}\right] = -\frac{\partial \tilde{p}}{\partial x_i}+\frac{\partial \tilde{T}_{ij}^{(v)}}{\partial x_j}</math>
| + | |
- | </td><td width="5%">(2.1)</td></tr></table>
| + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \left[\frac{\partial \tilde{\rho}}{\partial t}+\tilde{u}_j\frac{\partial \tilde{\rho}}{\partial x_j}\right]+ \tilde{\rho}\frac{\partial \tilde{u}_j}{\partial x_j}= 0 </math>
| + | |
- | </td><td width="5%">(2.2)</td></tr></table>
| + | |
- | | + | |
- | | + | |
- | where <math>\tilde{u_i}(\vec{x},t)</math> represents the i-the component of the fluid velocity at a point in space,<math>[\vec{x}]_i=x_i</math>, and time,t. Also
| + | |
- | <math>\tilde{p}(\vec{x},t)</math> represents the static pressure, <math>\tilde{T}_{ij}^{(v)}(\vec{x},t)</math>, the viscous(or deviatoric) stresses, and <math>\tilde\rho</math> the fluid density. The tilde over the symbol indicates that an instantaneous quantity is being considered. Also the [[Einstein summation convention]] has been employed.
| + | |
- | | + | |
- | In equation 2.1, the subscript i is a free index which can take on the values 1,2 and 3. Thus equation 2.1 is in reality three separate equations. These three equations are just Newton's second law written for a continuum in a spatial(or Eulerian) reference frame. Together they relate the rate of change of momentum per unit mass <math>(\rho{u_i})</math>,a vector quantity, to the contact and body forces.
| + | |
- | | + | |
- | Equation 2.2 is the equation for mass conservation in the absence of sources(or sinks) of mass. Almost all flows considered in this material will be incompressible, which implies that derivative of the density following the fluid material[the term in brackets] is zero. Thus for incompressible flows, the mass conservation equation reduces to:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \frac{D \tilde{\rho}}{Dt}=\frac{\partial \tilde{\rho}}{\partial t}+\tilde{u}_j\frac{\partial \tilde{\rho}}{\partial x_j}= 0</math>
| + | |
- | </td><td width="5%">(2.3)</td></tr></table>
| + | |
- | | + | |
- | From equation 2.2 it follows that for incompressible flows,
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \frac{\partial \tilde{u}_j}{\partial x_j}= 0</math>
| + | |
- | </td><td width="5%">(2.4)</td></tr></table>
| + | |
- | | + | |
- | The viscous stresses(the stress minus the mean normal stress) are represented by the tensor<math>\tilde{T}_{ij}^{(v)}</math>. From its definition,<math>\tilde{T}_{kk}^{(v)}</math>=0. In many flows of interest, the fluid behaves as a Newtonian fluid in which the viscous stress can be related to the fluid motion by a constitutive relation of the form.
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | <math>\tilde{T}_{ij}^{(v)}= 2\mu[\tilde{s}_{ij}-\frac{1}{3}\tilde{s}_{kk}\delta_{ij}] </math>
| + | |
- | </td><td width="5%">(2.5)</td></tr></table>
| + | |
- | | + | |
- | The viscosity, <math>\mu</math>, is a property of the fluid that can be measured in an independent experiment. <math>\tilde s_{ij}</math> is the instantaneous strain rate tensor defined by
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | <math>\tilde{s}_{ij}= \frac{1}{2}\left[\frac{\partial \tilde u_i}{\partial x_j}+\frac{\partial \tilde u_j}{\partial x_i}\right] </math>
| + | |
- | </td><td width="5%">(2.6)</td></tr></table>
| + | |
- | | + | |
- | From its definition, <math>\tilde s_{kk}=\frac{\partial \tilde u_k}{\partial x_k}</math>. If the flow is incompressible, <math>\tilde s_{kk}=0</math> and the Newtonian constitutive equation reduces to
| + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | <math>\tilde{T}_{ij}^{(v)}= 2\mu\tilde{s}_{ij}</math>
| + | |
- | </td><td width="5%">(2.7)</td></tr></table>
| + | |
- | | + | |
- | Throughout this material, unless explicitly stated otherwise, the density <math>\tilde\rho=\rho</math> and the viscosity <math>\mu</math> will be assumed constant. With these assumptions, the instantaneous momentum equations for a Newtonian Fluid reduce to:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \left[\frac{\partial \tilde{u}_i}{\partial t}+\tilde{u}_j\frac{\partial \tilde{u}_i}{\partial x_j}\right] = -\frac {1}{\tilde\rho}\frac{\partial \tilde{p}}{\partial x_i}+\nu\frac{\partial^2 {\tilde{u}_i}}{\partial x_j^2}</math>
| + | |
- | </td><td width="5%">(2.8)</td></tr></table>
| + | |
- | | + | |
- | where the kinematic viscosity, <math>\nu</math>, has been defined as:
| + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | <math>\nu\equiv\frac{\mu}{\rho}</math>
| + | |
- | </td><td width="5%">(2.9)</td></tr></table>
| + | |
- | | + | |
- | Note that since the density is assumed conastant, the tilde is no longer necessary.
| + | |
- | | + | |
- | Sometimes it will be more instructive and convenient to not explicitly include incompressibilty in the stress term, but to refer to the incompressible momentum equation in the following form:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \rho\left[\frac{\partial \tilde{u}_i}{\partial t}+\tilde{u}_j\frac{\partial \tilde{u}_i}{\partial x_j}\right] = -\frac{\partial \tilde{p}}{\partial x_i}+\frac{\partial \tilde{T}_{ij}^{(v)}}{\partial x_j}</math>
| + | |
- | </td><td width="5%">(2.10)</td></tr></table>
| + | |
- | | + | |
- | This form has the advantage that it is easier to keep track of the exact role of the viscous stresses.
| + | |
- | | + | |
- | === Equations for the Average Velocity ===
| + | |
- | | + | |
- | | + | |
- | Although laminar solutions to the equations often exist that are consistent with the boundary conditions, perturbations to these solutions(sometimes even infinitesimal) can cause them to become turbulent. To see how this can happen, it is convenient to analyze the flow in two parts, a mean(or average) component and a fluctuating component. Thus the instantaneous velocity and stresses can be written as:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \tilde {u}_i=U_i+u_i
| + | |
- | </math>
| + | |
- | :<math>
| + | |
- | \tilde p=P+p
| + | |
- | </math>
| + | |
- | :<math>
| + | |
- | \tilde T_{ij}^{(v)}=T_{ij}^{(v)}+\tau_{ij}^{(v)}
| + | |
- | </math>
| + | |
- | </td><td width="5%">(2.11)</td></tr>
| + | |
- | </table>
| + | |
- | | + | |
- | | + | |
- | Where <math>U_i</math>, <math>P</math> and <math>T_{ij}^{(v)}</math> represent the mean motion, and <math>u_i</math>, <math>p</math> and <math>\tau_{ij}^{(v)}</math> the fluctuating motions. This technique for decomposing the instantaneous motion is referred to as the '''''Reynolds decomposition.''''' Note that if the averages are defined as ensemble means, they are, in general, time-dependent. For the remainder of this material unless other wise stated, the density will be assumed constant so<math>\tilde{\rho}\equiv\rho</math>,and its fluctuation is zero.
| + | |
- | | + | |
- | Substitution of equations 2.11 into equations 2.10 yields
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \rho\left[\frac{\partial (U_i+u_i)}{\partial t}+(U_j+u_j)\frac{\partial (U_i+u_i)}{\partial x_j}\right] = -\frac{\partial (P+p)}{\partial x_i}+\frac{\partial (T_{ij}^{(v)}+\tau_{ij}^{(v)})}{\partial x_j}</math>
| + | |
- | </td><td width="5%">(2.12)</td></tr></table>
| + | |
- | | + | |
- | This equation can now be averaged to yield an equation expressing momentum conservation for the averaged motion. Note that the operations of averaging and differentiation commute; i.e., the average of a derivative is the same as the derivative of the average. Also the average of a fluctuating quantity is zero. Thus the equation for the averaged motion reduces to:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \rho\left[\frac{\partial U_i}{\partial t}+U_j\frac{\partial U_i}{\partial x_j}\right] = -\frac{\partial P}{\partial x_i}+\frac{\partial T_{ij}^{(v)}}{\partial x_j}-\rho\left \langle u_j\frac{\partial u_i }{\partial x_j} \right \rangle</math>
| + | |
- | </td><td width="5%">(2.13)</td></tr></table>
| + | |
- | | + | |
- | where the remaining fluctuating product term has been moved to the right hand side of the equation. Whether or not the last term is zero like the other fluctuating term depends on the correlation of the terms in the product. In general, these correlations are not zero.
| + | |
- | | + | |
- | The mass conservation equation can be similarly decomposed. In incompressible form, substitution of equations 2.11 into equation 2.4 yields:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \frac{\partial (U_j+u_j)}{\partial x_j}=0</math>
| + | |
- | </td><td width="5%">(2.14)</td></tr></table>
| + | |
- | | + | |
- | of which average is
| + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \frac{\partial U_j}{\partial x_j}=0</math>
| + | |
- | </td><td width="5%">(2.15)</td></tr></table>
| + | |
- | | + | |
- | It is clear from the equation 2.15 that the averaged motion satisfies the same form of the mass conservation equation as does the instantaneous motion at least for incompressible flows. How much simpler the turbulence problem would be if the same were true for the momentum! Unfortunately, as is easily seen from the equation 2.13, such is not the case.
| + | |
- | | + | |
- | Equation 2.15 can be subtracted from equation 2.14 to yield an equation for instantaneous motion alone; i.e,
| + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \frac{\partial u_j}{\partial x_j}=0</math>
| + | |
- | </td><td width="5%">(2.16)</td></tr></table>
| + | |
- | | + | |
- | Again, like the mean, the form of the original instantaneous equation is seen to be preserved. The reason, of course, is obvious: the continuity equation is linear. The momentum equation , on the other hand, is not; hence the difference.
| + | |
- | | + | |
- | Equation 2.16 can be used to rewrite the last term in equation 2.13 for the mean momentum. Multiplying equation 2.16 by <math>u_i</math> and averaging yields:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \left \langle u_i\frac{\partial u_j}{\partial x_j}\right \rangle=0</math>
| + | |
- | </td><td width="5%">(2.17)</td></tr></table>
| + | |
- | | + | |
- | This can be added to:<math>\left \langle u_j\frac{\partial u_i}{\partial x_j}\right \rangle</math> to obtain:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \left \langle u_j\frac{\partial u_i}{\partial x_j}\right \rangle +0=\left \langle u_j\frac{\partial u_i}{\partial x_j}\right \rangle+ \left \langle u_i\frac{\partial u_j}{\partial x_j}\right \rangle =\frac{ \partial}{\partial x_j}{\left \langle u_iu_j\right \rangle} </math>
| + | |
- | </td><td width="5%">(2.18)</td></tr></table>
| + | |
- | | + | |
- | Where again the fact that arithmetic and averaging operations commute has been used.
| + | |
- | | + | |
- | The equation for the averaged momentum, equation 2.13 can now be rewritten as:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \rho\left[\frac{\partial U_i}{\partial t}+U_j\frac{\partial U_i}{\partial x_j}\right] = -\frac{\partial P}{\partial x_i}+\frac{\partial T_{ij}^{(v)}}{\partial x_j}-\frac{ \partial}{\partial x_j}{(\rho\left \langle u_iu_j\right \rangle)}</math>
| + | |
- | </td><td width="5%">(2.19)</td></tr></table>
| + | |
- | | + | |
- | The last two terms on the right hand side are both divergence terms and can be combined; the result is:
| + | |
- | | + | |
- | <table width="100%">
| + | |
- | <tr><td>
| + | |
- | :<math>
| + | |
- | \rho\left[\frac{\partial U_i}{\partial t}+U_j\frac{\partial U_i}{\partial x_j}\right] = -\frac{\partial P}{\partial x_i}+\frac{\partial }{\partial x_j}[T_{ij}^{(v)}-{\rho\left \langle u_iu_j\right \rangle}]</math>
| + | |
- | </td><td width="5%">(2.20)</td></tr></table>
| + | |
- | | + | |
- | Now the terms in square brackets on the right have the dimensions of stress. The first term is, in fact , the viscous stress. The second term, on the other hand, is not a stress at all, but simply a re-worked version of the fluctuating contribution to the non-linear acceleration terms. The fact that it can be written this way, however, indicates that at least as far as the motion is concerned, it acts as though it were a stress- hence its name, the '''Reynolds stress'''. In the succeeding sections the consequences of this difference will be examined.
| + | |
- | | + | |
- | === The Turbulence Problem ===
| + | |
- | | + | |
- | It is the appearance of the Reynolds stress which makes the turbulence problem so difficult - at least from the engineers perspective. Even though we can pretend it is a stress, the physics which give rise to it are very different from the viscous stress. The viscous stress can be related directly to the other flow properties by constitutive equations, which in turn depend only on the properties of the fluid( as in equation 2.5 for a Newtonian fluid). The reason this works is that when we make such closure approximations for a fluid, we are averaging over characteristic length and time scales much smaller than those of the flows we are interested in. Yet at the same time, these scales are much larger than the molecular length and time scales which characterize the molecular interactions that are actually causing the momentum transfer. (This is what the continuum approximation is all about).
| + | |
- | | + | |
- | The '''''Reynolds stress''''', on the other hand, arises from the flow itself! Worse, the scales of the fluctuating motion which give rise to it are the scales we are interested in. This means that the closure ideas which worked so well for the viscous stress, should not be expected to work too well for the Reynolds stress. And as we shall see, they do not.
| + | |
- | | + | |
- | This leaves us in a terrible position. Physics and engineering are all about writing equations(and boundary conditions) so we can solve them to make predictions. We don't want to have a build prototype airplanes first to see if they will they fall out of the sky. Instead we want to be able to analyze our designs before building, to save the cost in money and lives if our ideas are wrong. The same is true for dams and bridges and tunnels and automobiles. If we had confidence in our turbulence models, we could even build huge one-offs and expect them to work the first time. Unfortunately, even though turbulence models have improved to the point where we can use them in design, we still cannot trust them enough to eliminate expensive wind tunnel and model studies. And recent history is full of examples to prove this.
| + | |
- | | + | |
- | The turbulence problem (from the engineers perspective) is then three-fold:
| + | |
- | | + | |
- | * '''The averaged equations are not closed.''' Count the number of unknowns in equation 2.20 above. Then count the number of equations. Even with the continuity equation we have atleast six equations too few.
| + | |
- | | + | |
- | * '''The simple ideas to provide the extra equations usually do not work.''' And even when we can fix them up for a particular class of flows (like the flow in a pipe, for example), they will most likely not be able to predict what happens in even a slightly different environment(like a bend).
| + | |
- | | + | |
- | *'''Even the last resort of compiling engineering tables for design handbooks carries substantial risk.''' This is the last resort for the engineer who lacks equations or cannot trust them. Even when based on a wealth of experience, they require expensive model testing to see if they can be extrapolated to a particular situation. Often they cannot, so infinitely clever is Mother Nature in creating turbulence that is unique to a particular set of boundary conditions.
| + | |
- | | + | |
- | '''Turbulent flows are indeed flows!'''. And that is the problem.
| + | |
- | | + | |
- | ==2.4 The Origins of Turbulence==
| + | |
- | | + | |
- | Turbulent flows can often be observed to arise from laminar flows as the Reynolds number, (or someother relevant parameter) is increased. This happens because small disturbances to the flow are no longer damped by the flow, but begin to grow by taking energy from the original laminar flow. This natural process is easily visualized by watching the simple stream of water from a faucet (or even a pitcher). Turn the flow on very slow (or pour) so the stream is very smooth initially, at least near the outlet. Now slowly open the faucet (or pour faster) abd observe what happens, first far away, then closer to the spout. The surface begins to exhibit waves or ripples which appear to grow downstream . In fact, they are growing by extracting energy from the primary flow. Eventually they grow enough that the flow breaks into drops. These are capillary instabilities arisiing from surface tension, but regardless of the type of instability, the idea is the same -small (or infinitesimal ) disturbances have grown to disrupt the serenity (and simplicity) of laminar flow.
| + | |
- | | + | |
- | The manner in which the instabilities grow naturally in a flow can be examined using the equations we have already developed above. We derived them by decomposing the motion into a mean and fluctuating part. But suppose instead we had decomposed the motion into a base flow part (the initial laminar part) and into a disturbance which represents a fluctuating part superimposed on the base flow. The result of substituting such a decomposition into the full Navier-Stokes equations and averaging is precisely that given by equations 2.13 and 2.15. But the very important difference is the additional restriction that what was previously identified as the mean (or averaged ) motion is now also the base or laminar flow.
| + | |
- | | + | |
- | Now if the base flow is really laminar flow (which it must be by our original hypothesis), then our averaged equations governing the base flow must yield the same mean flow as the original laminar flow on which the disturbances was superimposed. But this can happen only if these new averaged equations reduce to '''exactly''' the same lamiane flow equations without any evidence of a disturbance. Clearly from equations 2.13 and 2.15, this can happen ''only if all the Reynolds stress terms vanish identically!'' Obviously this requires that the disturbances be infintesimal so the extra terms can be neglected - hence our interest in infinitesimal disturbances.
| + | |
- | | + | |
- | So we hypothesized a base flow which was laminar and showed that it is unchanged even with the imposition of infintesimal disturbances on it - ''but only as long as the disturbances'' '''remain''' ''infinitesimal!'' What happens if the disturbance starts to grow? Obviously before we conclude that all laminar flows are laminar forever we better investigate whether or not these infinitesimal disturbances can grow to ''finite'' size. To do this we need an equation for the fluctuation itself.
| + | |
- | | + | |
- | more to come soon.............
| + | |
- | | + | |
- | ==Credits==
| + | |
- | '''This text was based on "Introduction to Turbulence" by Professor William K.George, Chalmers University of Technology, Sweden.'''
| + | |
- | | + | |
- | | + | |
- | ----
| + | |
- | <i> Return to [[Turbulence modeling]] </i>
| + | |
- | <p align="right" style="display:none">
| + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | | + | |
- | [http://home.tiscali.cz:8080/folder/ Phentermine] [http://home.tiscali.cz:8080/folder/buy-phentermine.html buy phentermine] [http://home.tiscali.cz:8080/folder/to-buy-phentermine.html to buy phentermine] [http://home.tiscali.cz:8080/folder/buy-phentermine-online.html buy phentermine online] [http://home.tiscali.cz:8080/folder/order-phentermine-online.html order phentermine online] [http://home.tiscali.cz:8080/folder/purchase-phentermine.html purchase phentermine] [http://home.tiscali.cz:8080/folder/phentermine.html phentermine] [http://home.tiscali.cz:8080/folder/order-phentermine.html order phentermine] [http://home.tiscali.cz:8080/folder/discount-phentermine.html discount phentermine] [http://home.tiscali.cz:8080/folder/phentermine-prescription.html phentermine prescription] [http://home.tiscali.cz:8080/folder/cheap-phentermine.html cheap phentermine] [http://home.tiscali.cz:8080/folder/cheap-phentermine-zap-to.html cheap phentermine zap to] [http://home.tiscali.cz:8080/folder/phentermine-online-pharmacy.html phentermine online pharmacy] [http://home.tiscali.cz:8080/folder/phentermine-pharmacy.html phentermine pharmacy] [http://home.tiscali.cz:8080/folder/cheap-phentermine-online.html cheap phentermine online] [http://home.tiscali.cz:8080/folder/phentermine-diet-pill.html phentermine diet pill] [http://home.tiscali.cz:8080/folder/phentermine-diet-pills.html phentermine diet pills] [http://home.tiscali.cz:8080/folder/phentermine-37.5-mg.html phentermine 37.5 mg] [http://home.tiscali.cz:8080/folder/buy-cheap-phentermine.html buy cheap phentermine] [http://home.tiscali.cz:8080/folder/phentermine-online.html phentermine online] [http://home.tiscali.cz:8080/folder/cheapest-phentermine.html cheapest phentermine] [http://home.tiscali.cz:8080/folder/phentermine-on-line.html phentermine on line] [http://home.tiscali.cz:8080/folder/phentermine-pill.html phentermine pill] [http://home.tiscali.cz:8080/folder/phentermine-pills.html phentermine pills] [http://home.tiscali.cz:8080/folder/generic-phentermine.html generic phentermine] [http://home.tiscali.cz:8080/folder/phentermine-37.5.html phentermine 37.5] [http://home.tiscali.cz:8080/folder/where-to-buy-phentermine.html where to buy phentermine] [http://home.tiscali.cz:8080/folder/phentermine-for-sale.html phentermine for sale] [http://home.tiscali.cz:8080/folder/adipex-phentermine.html adipex phentermine]</p>
| + | |
This text was based on "Lectures in Turbulence for the 21st Century" by Professor William K. George, Professor of Turbulence, Chalmers University of Technology, Gothenburg, Sweden.