CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > CFX

control variable bound in cfx

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   April 13, 2009, 05:46
Default control variable bound in cfx
  #1
New Member
 
Join Date: Mar 2009
Posts: 2
Rep Power: 0
klarke is on a distinguished road
HI,everyone
I am doing a compressor transient research,it have run a lot of time step,but suddenly,it stopped like below
Error in subroutine GET_SPECVAR :
Specified values for Total Temperature are out of bounds on Outlet GETVAR originally called by subroutine CAL_ENTHTOT). So did you have any experience of this error or how to control the varible bound.Thanks a lot!
klarke is offline   Reply With Quote

Old   April 16, 2009, 16:01
Default
  #2
Senior Member
 
Join Date: Mar 2009
Location: Europe
Posts: 168
Rep Power: 9
joey2007 is on a distinguished road
Take a intermediate result or backup and check the total temperature. Suppose the result is unphysical.
joey2007 is offline   Reply With Quote

Old   June 23, 2014, 07:00
Default
  #3
Member
 
Daniel Frederik
Join Date: Apr 2014
Location: Switzerland
Posts: 38
Rep Power: 4
Daniel Frederik is on a distinguished road
If the result is unphisical is there still a way to make it work or does that mean, that it is phisically impossible to simulate that case?
Daniel Frederik is offline   Reply With Quote

Old   June 23, 2014, 19:29
Default
  #4
Super Moderator
 
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 12,832
Rep Power: 100
ghorrocks is a jewel in the roughghorrocks is a jewel in the roughghorrocks is a jewel in the rough
This could be caused by a numerical wander which will pass and it will eventually converge to the correct value, or it could be that the simulation was not physically possible in the first place.

I would save a results file just before the crash and see what it look like.
ghorrocks is offline   Reply With Quote

Old   June 24, 2014, 06:29
Default
  #5
Member
 
Daniel Frederik
Join Date: Apr 2014
Location: Switzerland
Posts: 38
Rep Power: 4
Daniel Frederik is on a distinguished road
Thank you Glenn,
I solved the problem now by using a initial File of a previous run with other boundary condition values. For some reason the Total Temperature went out of bounds without an adequate initial guess.
Daniel Frederik is offline   Reply With Quote

Old   June 24, 2014, 19:15
Default
  #6
Super Moderator
 
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 12,832
Rep Power: 100
ghorrocks is a jewel in the roughghorrocks is a jewel in the roughghorrocks is a jewel in the rough
This is quite common. That is why a good initial condition helps a lot.
ghorrocks is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
cfx time scale control Kordou CFX 2 September 22, 2008 11:07
Assign new variable in CFX Post Ben CFX 1 August 25, 2008 14:59
error in COMSOL:'ERROR:6164 Duplicate Variable' bhushas Main CFD Forum 1 May 30, 2008 04:35
hi how to set entironment variable in CFX pre romance CFX 0 December 23, 2007 08:11
Replace periodic by inlet-outlet pair lego CFX 3 November 5, 2002 21:09


All times are GMT -4. The time now is 12:00.