|
[Sponsors] |
February 3, 2013, 23:30 |
SU2 running
|
#1 |
New Member
Join Date: Feb 2013
Posts: 3
Rep Power: 13 |
When I run SU2_CFD.exe, it is not opening and the message says "There is configuration file!""Press any key to exit" I could not find anything in .cfg format in the installation directory. I have downloaded the windows 32 bit version and installed it along with the intel exe installation. But still this error comes. Please help me solve this problem. Is there any place where can i download configuration file??? I could not find it on google.
|
|
February 3, 2013, 23:37 |
|
#2 |
Senior Member
Cean
Join Date: Feb 2010
Posts: 128
Rep Power: 16 |
you have to download the testcase and run the program inside a case folder where a cfg file is stored.
|
|
February 4, 2013, 03:46 |
SU2 running
|
#3 |
New Member
Join Date: Feb 2013
Posts: 3
Rep Power: 13 |
Thank You very much for your reply! I downloaded test case as u said and tried to open the case inside it but still it is saying no configuration file! do i have to paste the downloaded test case in the home directory??? what is the program to read those cfg files?? It says unsupported format. Please help!
|
|
February 4, 2013, 05:24 |
|
#4 |
Senior Member
Cean
Join Date: Feb 2010
Posts: 128
Rep Power: 16 |
||
February 5, 2013, 17:16 |
|
#5 |
Member
Join Date: Jun 2011
Posts: 51
Rep Power: 14 |
Hi,
Did you run it locally? I think that you need to run it in the folder where u have all the files: mesh, setup and .exe. Regards |
|
February 5, 2013, 23:32 |
|
#6 |
New Member
Join Date: Feb 2013
Posts: 3
Rep Power: 13 |
cfdivan,
Thank you so much for the tip. But I ran it locally by clicking on the .exe file in the Stanford ADL directory, which also contains my mesh files, test cases ,etc. But still it is showing the same error. Did u get any configuration file while downloading?? should i need to install any other s/w to get it running on my windows?? or shall i try binary version?? Please reply! |
|
February 5, 2013, 23:52 |
|
#7 |
Senior Member
Cean
Join Date: Feb 2010
Posts: 128
Rep Power: 16 |
You need to read the manual more.
Run in a DOS terminal and speify the cfg file in your command line. |
|
February 6, 2013, 05:20 |
|
#8 |
Member
Join Date: Jun 2011
Posts: 51
Rep Power: 14 |
Hi ellipsis,
Try in your prompt: C:\Program Files (x86)\Stanford ADL\SU2\bin>SU2_CFD.exe inv_channel.cfg Should work. Just let me know. Regrads |
|
February 25, 2013, 02:38 |
|
#9 |
New Member
Join Date: Feb 2013
Posts: 2
Rep Power: 0 |
Hi. I'm also a beginner. I managed to run the quick start tutorial but I did'nt get any results!
|
|
February 25, 2013, 09:02 |
|
#10 |
New Member
Join Date: Feb 2013
Posts: 2
Rep Power: 0 |
Hi....
I managed to relsove this by my self! The "bin" directory where I run SU2_CFD.exe was in "program files" folder, which is sort of "write protected". Every thing gone well when I copied "bin" to "Documents" and ran the exe from there. I hope this might help someone. Thanks all. |
|
March 13, 2013, 15:29 |
malik
|
#11 |
New Member
malik
Join Date: Nov 2012
Posts: 19
Rep Power: 13 |
Hi everyone,
I am using SU2 code for the first time. I want to run it on windows 7 or linux whichever is easy. I have downloaded the test cases, source code that contains trunk folder as well and binary file needed for windows (i am running on 32 bit macihne). I want to run the ONERA M6 wing and i have also transferred the mesh files and two other from test caes/euler/onera m6 to serial folder in source code but the code is not working, it says that there is a configuration file , press any key to exit. i have also tried to run it on linux (for that i downloaded binary for linux) but there is a permission denied error and tried it with chmod 777 but then again its not working. Any help will be greatly appreciated Thanks in advance |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
parallel error with cyclic BCs for pimpleDyMFoam and trouble in resuming running | sunliming | OpenFOAM Bugs | 21 | November 22, 2013 03:38 |
Welcome to the Stanford University Unstructured (SU2) forum! | economon | SU2 | 0 | January 7, 2013 02:48 |
New SU2 Forum Opened at CFD Online | pete | Site News & Announcements | 0 | January 5, 2013 17:59 |
Stanford University Unstructured (SU2) Open-Source Code Released Today | praveen | Main CFD Forum | 1 | May 21, 2012 20:52 |
Kubuntu uses dash breaks All scripts in tutorials | platopus | OpenFOAM Bugs | 8 | April 15, 2008 07:52 |