# Spalart-Allmaras model

(Difference between revisions)
 Revision as of 09:32, 15 September 2005 (view source)Jola (Talk | contribs)m← Older edit Revision as of 19:18, 1 September 2006 (view source)Odlopez (Talk | contribs) (→Original model)Newer edit → Line 45: Line 45: C_{t4} &=& 2 C_{t4} &=& 2 \end{matrix} \end{matrix} + [/itex] + + According to Spalart it is safer to use the following values for the last two constants: + :$+ \begin{math} + C_{t3} &=& 1.2 \\ + C_{t4} &=& 0.5 + \end{matrix}$ [/itex]

## Revision as of 19:18, 1 September 2006

Spallart-Allmaras model is a one equation model for the turbulent viscosity.

## Original model

The turbulent eddy viscosity is given by

$\nu_t = \tilde{\nu} f_{v1}, \quad f_{v1} = \frac{\chi^3}{\chi^3 + C^3_{v1}}, \quad \chi := \frac{\tilde{\nu}}{\nu}$
$\frac{\partial \tilde{\nu}}{\partial t} + u_j \frac{\partial \tilde{\nu}}{\partial x_j} = C_{b1} [1 - f_{t2}] \tilde{S} \tilde{\nu} + \frac{1}{\sigma} \{ \nabla \cdot [(\nu + \tilde{\nu}) \nabla \tilde{\nu}] + C_{b2} | \nabla \nu |^2 \} - \left[C_{w1} f_w - \frac{C_{b1}}{\kappa^2} f_{t2}\right] \left( \frac{\tilde{\nu}}{d} \right)^2 + f_{t1} \Delta U^2$
$\tilde{S} \equiv S + \frac{ \tilde{\nu} }{ \kappa^2 d^2 } f_{v2}, \quad f_{v2} = 1 - \frac{\chi}{1 + \chi f_{v1}}$
$f_w = g \left[ \frac{ 1 + C_{w3}^6 }{ g^6 + C_{w3}^6 } \right]^{1/6}, \quad g = r + C_{w2}(r^6 - r), \quad r \equiv \frac{\tilde{\nu} }{ \tilde{S} \kappa^2 d^2 }$
$f_{t1} = C_{t1} g_t \exp\left( -C_{t2} \frac{\omega_t^2}{\Delta U^2} [ d^2 + g^2_t d^2_t] \right)$
$f_{t2} = C_{t3} \exp(-C_{t4} \chi^2)$

The constants are

$\begin{matrix} \sigma &=& 2/3\\ C_{b1} &=& 0.1355\\ C_{b2} &=& 0.622\\ \kappa &=& 0.41\\ C_{w1} &=& C_{b1}/\kappa^2 + (1 + C_{b2})/\sigma \\ C_{w2} &=& 0.3 \\ C_{w3} &=& 2 \\ C_{v1} &=& 7.1 \\ C_{t1} &=& 1 \\ C_{t2} &=& 2 \\ C_{t3} &=& 1.1 \\ C_{t4} &=& 2 \end{matrix}$

According to Spalart it is safer to use the following values for the last two constants:

Failed to parse (unknown function\begin): \begin{math} C_{t3} &=& 1.2 \\ C_{t4} &=& 0.5 \end{matrix}

## Model for compressible flows

There are two approaches to adapting the model for compressible flows. In the first approach the turbulent dynamic viscosity is computed from

$\mu_t = \rho \tilde{\nu} f_{v1}$

where $\rho$ is the local density. The convective terms in the equation for $\tilde{\nu}$ are modified to

$\frac{\partial \tilde{\nu}}{\partial t} + \frac{\partial}{\partial x_j} (\tilde{\nu} u_j)= \mbox{RHS}$

where the right hand side (RHS) is the same as in the original model.

## References

• Spalart, P. R. and Allmaras, S. R. (1992), "A One-Equation Turbulence Model for Aerodynamic Flows", AIAA Paper 92-0439.