CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

Interpolating Segment-Result on Full-Cylinder-Model as initial Condition

Register Blogs Community New Posts Updated Threads Search

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   February 14, 2018, 14:31
Cool Interpolating Segment-Result on Full-Cylinder-Model as initial Condition
  #1
Member
 
Philipp Wiedemer
Join Date: Dec 2016
Location: Munich, Germany
Posts: 42
Rep Power: 9
MangoNrFive is on a distinguished road
Hello

What?
I would like to simulate the influence of a non-centric rotor-Position on a leaf-seal. My plan was to start with a small segment with periodic bc. After doing sensitivity studies etc. i would like to interpolate the results on the full 360°-model as initial condition. For this purpose i can interpolate onto a model with centric rotor first and move the rotor later.

Why?
The segment-simulation already takes relatively long to converge. Since the geometry is axialsymmetric i don't expect major periodic phenomena thus the rotational interpolation should be a very good initial condition.

How?
Is there any way of doing this? It should be a common idea to interpolate a periodic segment on a full model, but i couldn't find any solution.

I use ICEM for meshing and CFX for the solver, pre- and postprocessing.

Thanks for reading this
MangoNrFive is offline   Reply With Quote

Old   February 15, 2018, 03:32
Default
  #2
Senior Member
 
M
Join Date: Dec 2017
Posts: 698
Rep Power: 12
AtoHM is on a distinguished road
It is implemented in CFX. In Pre, go to Execution Control -> Initial Values. Add an Initial Values Item with your segment result. Then, add a Interpolation Mapping Item and tick replication control. Here you can give the rotation axis and set up your interpolation.
In my case there is a turbine rotor with 1 blade per passage. There are 65 blade in total. I want 4 of those together, so I used the numbers like:
Pass. in Component: 1; Passages in 360: 65; Total Num. Instances: 4; Theta Offset: 0.
I hope this helps.
AtoHM is offline   Reply With Quote

Old   February 15, 2018, 12:27
Default
  #3
Member
 
Philipp Wiedemer
Join Date: Dec 2016
Location: Munich, Germany
Posts: 42
Rep Power: 9
MangoNrFive is on a distinguished road
Thank you, exactly what i needed!
MangoNrFive is offline   Reply With Quote

Reply

Tags
cfx, initial condition, interpolation, periodic bc


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem with chtMultiregionFoam radiation boundary condition baran_foam OpenFOAM Running, Solving & CFD 10 December 17, 2019 18:36
Segmentation fault when using reactingFOAM for Fluids Tommy Floessner OpenFOAM Running, Solving & CFD 4 April 22, 2018 13:30
Compressor Simulation using rhoPimpleDyMFoam Jetfire OpenFOAM Running, Solving & CFD 107 December 9, 2014 14:38
Upgraded from Karmic Koala 9.10 to Lucid Lynx10.04.3 bookie56 OpenFOAM Installation 8 August 13, 2011 05:03
Orifice Plate with a fully developed flow - Problems with convergence jonmec OpenFOAM Running, Solving & CFD 3 July 28, 2011 06:24


All times are GMT -4. The time now is 19:34.