How to read the data?

joescor2 · December 7, 2016, 11:03

Hi!

I`m simulating the air flow in a circular pipe but I only need the heat transfer in the radial direction. I would like to know if there are any way to plot the temperature and the heat flux vs radial direction or at at least in the x or y direction.

Best regards,

jhuang · December 7, 2016, 17:30

You can use the Query function in Ensight to plot the temperature along a line in any direction. You can use the Calculator in Ensight to build your own function to calculate local heat flux.

The boundary heat flux can be output to post files by selecting Boundary/Film-Bound-Boundary Heat Flux in Studio's Post Variable Selection window.

Thanks.

joescor2 · December 12, 2016, 05:50

thanks..I was able to plot the temperature.

Now my proble it's with the geometry. I'm trying to import the object from solidworks but the file isn't imported with the same geometry reference and even trying to move the object with the translate option but there is always a little space which bothers for my simulation. Could you help with this problem?

Best regards!

jhuang · December 12, 2016, 10:56

CONVERGE Studio can do some basic CAD manipulations including scale, rotating, translating, etc. Can you explain more on the small gap problem? Thanks!

joescor2 · December 14, 2016, 04:49

Hi! I have checked the geometry and the reference location many times but the error continues. Do you know which is the reason of this problem?

I have another question.

I need to evaluate the influence of the roughness on the heat transfer in surfaces with a very low roughness. Is it necessary a mesh finer than the roughness? because according to the CONVERGE manual in the wall model the roughness is only a value in the equation and the software doesn't see the surface roughness fisically, is it?

Best Regards

December 7, 2016, 11:03	How to read the data?	#1
joescor2 New Member Join Date: Dec 2016 Posts: 13 Rep Power: 9	Hi! I`m simulating the air flow in a circular pipe but I only need the heat transfer in the radial direction. I would like to know if there are any way to plot the temperature and the heat flux vs radial direction or at at least in the x or y direction. Best regards,

December 7, 2016, 17:30		#2
jhuang New Member Jing Huang Join Date: Dec 2015 Location: Convergent Science, Madison WI Posts: 23 Rep Power: 10	You can use the Query function in Ensight to plot the temperature along a line in any direction. You can use the Calculator in Ensight to build your own function to calculate local heat flux. The boundary heat flux can be output to post files by selecting Boundary/Film-Bound-Boundary Heat Flux in Studio's Post Variable Selection window. Thanks. __________________ Jing Huang Research Engineer CONVERGECFD

December 12, 2016, 10:56		#4
jhuang New Member Jing Huang Join Date: Dec 2015 Location: Convergent Science, Madison WI Posts: 23 Rep Power: 10	CONVERGE Studio can do some basic CAD manipulations including scale, rotating, translating, etc. Can you explain more on the small gap problem? Thanks! __________________ Jing Huang Research Engineer CONVERGECFD

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cannot read 2nd column of data in libforces.so output force.dat file	musahossein	OpenFOAM Programming & Development	9	February 21, 2015 22:43
[Other] How to create an MRF zone ?	aminem	OpenFOAM Meshing & Mesh Conversion	2	December 8, 2014 10:45
problem when converting mesh (made by ICEM) using fluentMeshToFoam	Forrest_Lei	OpenFOAM	11	October 16, 2009 06:28
Read data file	R.B.M	FLUENT	0	July 10, 2002 23:16
Tecplot can't read data file from Fluent.	stephen	FLUENT	8	November 21, 2001 20:27

December 12, 2016, 05:50		#3
joescor2 New Member Join Date: Dec 2016 Posts: 13 Rep Power: 9	thanks..I was able to plot the temperature. Now my proble it's with the geometry. I'm trying to import the object from solidworks but the file isn't imported with the same geometry reference and even trying to move the object with the translate option but there is always a little space which bothers for my simulation. Could you help with this problem? Best regards!

December 14, 2016, 04:49		#5
joescor2 New Member Join Date: Dec 2016 Posts: 13 Rep Power: 9	Hi! I have checked the geometry and the reference location many times but the error continues. Do you know which is the reason of this problem? I have another question. I need to evaluate the influence of the roughness on the heat transfer in surfaces with a very low roughness. Is it necessary a mesh finer than the roughness? because according to the CONVERGE manual in the wall model the roughness is only a value in the equation and the software doesn't see the surface roughness fisically, is it? Best Regards