Temporal average problem

hebe2u. · December 22, 2016, 04:06

Hi

I have a question about averaging the data such as temperature, velocity, and etc. over time at each location of the entire domain.

About using 'Average of selected pot output files' option of post convert, what should I do to solve the following error.( the output files includes logic_i, logic_j, logic_k, level, and volume.)

The postfile is for CONVERGE version 2.3.
error: wrong output file format: please remove convert.in and try rerun post converter.

Please answer any hints.

Thank you!

SamWijey · December 22, 2016, 15:01

Hello,

Are you specifying a convert.in in your post_convert command? Simply type post_convert in the folder where you have the post out files and follow the prompted directions.

Thanks,

hebe2u. · December 22, 2016, 19:20

Thank you for your reply!

Actually I did it with CONVERGE studio!
However, the averaging problem is solved by specifying a convert.in in the command as you told me.

And I found that there is something wrong in post_convert.exe in CONVERGE stuido folder
I changed the path of post_convert in the settings of 'post-processing 3D' tab of CONVERGE studio from CONVERGE studio folder to CONVERGE folder.
Now it works well.

Thank you again.

December 22, 2016, 04:06	Temporal average problem	#1
hebe2u. New Member Hyojeong Lee Join Date: Sep 2016 Posts: 8 Rep Power: 9	Hi I have a question about averaging the data such as temperature, velocity, and etc. over time at each location of the entire domain. About using 'Average of selected pot output files' option of post convert, what should I do to solve the following error.( the output files includes logic_i, logic_j, logic_k, level, and volume.) The postfile is for CONVERGE version 2.3. error: wrong output file format: please remove convert.in and try rerun post converter. Please answer any hints. Thank you!

December 22, 2016, 15:01		#2
SamWijey Senior Member Sameera Wijeyakulasuriya Join Date: Jan 2016 Location: Convergent Science, Madison WI Posts: 117 Rep Power: 10	Hello, Are you specifying a convert.in in your post_convert command? Simply type post_convert in the folder where you have the post out files and follow the prompted directions. Thanks, __________________ Sameera Wijeyakulasuriya Principal Engineer, Applications CONVERGECFD

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
area does not match neighbour by ... % -- possible face ordering problem	St.Pacholak	OpenFOAM	10	February 7, 2024 21:50
y+ and u+ values with low-Re RANS turbulence models: utility + testcase	florian_krause	OpenFOAM	114	August 23, 2023 05:37
Floating point exception error	Alan	OpenFOAM Running, Solving & CFD	11	July 1, 2021 21:51
How to obtain turbulent kinetic energy data from LES model of Ansys CFX?	rsin	CFX	19	December 29, 2018 04:43
Problem for Mass flow average in Post...	ST	CFX	2	October 27, 2005 13:35

December 22, 2016, 19:20		#3
hebe2u. New Member Hyojeong Lee Join Date: Sep 2016 Posts: 8 Rep Power: 9	Thank you for your reply! Actually I did it with CONVERGE studio! However, the averaging problem is solved by specifying a convert.in in the command as you told me. And I found that there is something wrong in post_convert.exe in CONVERGE stuido folder I changed the path of post_convert in the settings of 'post-processing 3D' tab of CONVERGE studio from CONVERGE studio folder to CONVERGE folder. Now it works well. Thank you again.