cm vs alpha graph of an airplane on ansys fluent

titanan · August 28, 2023, 04:50

Hey everyone.
I have to find the cm (pitching moment coefficent) vs alpha graph of an airplane using ansys fluent. What is the aproach ı have to take to solve this problem.
Thanks already.

agd · August 28, 2023, 13:27

1. Build a grid of said aircraft
2. Set the angle of attacjk along with boundary conditions, freestream parameters and whatever else your flow solver needs.
3. Run the flow solver to generate a solution and compute the moment coefficient using the flow solution.
4. Plot the coefficient against that value of AOA.
5. Repeat steps 2-4 until you have generated a desired curve.

Now if you are looking for fluent specific knowledge, you might want to try the fluent specific forum.

titanan · August 29, 2023, 04:23

Hey
I see. I thought there woulld be a faster way than making a new mesh every time but that can work too.
Thanks for your suggestion.

siw · August 29, 2023, 09:25

You do not have to make a new mesh for each AoA. Just make a suitable mesh and change the freestream velocity components for each simulation.

In Fluent there is the far-field boundary condition for this type of simulation. It's efficient to make a spherical (full-aircraft) or hemispherical (half-aircraft due to symmetry) computational domain.

August 28, 2023, 04:50	cm vs alpha graph of an airplane on ansys fluent	#1
titanan New Member Join Date: Jul 2023 Posts: 12 Rep Power: 2	Hey everyone. I have to find the cm (pitching moment coefficent) vs alpha graph of an airplane using ansys fluent. What is the aproach ı have to take to solve this problem. Thanks already.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how to run fluent from matlab without using aas toolbox?	artemis96	ANSYS	7	May 23, 2022 12:16
[ANSYS Meshing] How do I open a mesh made in Ansys Fluent 2020 R2 on Ansys Fluent 2019 R3?	Ryan T	ANSYS Meshing & Geometry	3	November 3, 2021 15:44
Ansys Fluent meshing vs Ansys Meshing	amd2424	FLUENT	1	May 10, 2021 03:15
How to open Icem mesh in Ansys Fluent?	emmkell	FLUENT	27	February 6, 2018 03:34
Can you help me with a problem in ansys static structural solver?	sourabh.porwal	Structural Mechanics	0	March 27, 2016 17:07

August 28, 2023, 13:27		#2
agd Senior Member Join Date: Jul 2009 Posts: 357 Rep Power: 18	1. Build a grid of said aircraft 2. Set the angle of attacjk along with boundary conditions, freestream parameters and whatever else your flow solver needs. 3. Run the flow solver to generate a solution and compute the moment coefficient using the flow solution. 4. Plot the coefficient against that value of AOA. 5. Repeat steps 2-4 until you have generated a desired curve. Now if you are looking for fluent specific knowledge, you might want to try the fluent specific forum.

August 29, 2023, 04:23		#3
titanan New Member Join Date: Jul 2023 Posts: 12 Rep Power: 2	Hey I see. I thought there woulld be a faster way than making a new mesh every time but that can work too. Thanks for your suggestion.

August 29, 2023, 09:25		#4
siw Senior Member Stuart Join Date: Jul 2009 Location: Portsmouth, England Posts: 735 Rep Power: 25	You do not have to make a new mesh for each AoA. Just make a suitable mesh and change the freestream velocity components for each simulation. In Fluent there is the far-field boundary condition for this type of simulation. It's efficient to make a spherical (full-aircraft) or hemispherical (half-aircraft due to symmetry) computational domain.