[ships26]

Originally Posted by Simbelmynë

3. I cannot reassure anything. Many motherboard manufacturers list different configurations on their QVL. If you wish to increase your likelihood of hitting high memory overclock then you should assert that the memory layout is Daisy Chain in case you go for 2 memory sticks. If you go for 4 sticks then you want a T-topology. Daisy Chain is the most common in X570 boards. Your memory is probably going to work just fine, Zen2 is much more forgiving when it comes to memory overclock compared to previous generations.

So, I think I wasn't very clear about this question. I was trying to ask: if the QVL of the x299 motherboard has this memory listed as working with 4 DIMMS, could I buy 2 sets and still be sure it will not only work, but also in quad-channel? It just struck me as bit odd that they would do that for a dual stick kit. I also understand that you can't tell me that it'll work for sure, because who knows? I know Intel is known to usually be pretty good in terms of compatibility, though, and I'm willing to take that risk for the price differences to the x4 kits I'm coming up with.
Anyway, it worked out well since you opened my eyes for the memory topology of the amd motherboards. Maybe I should, but I didn't know about that, thanks for pointing it out!

About 4, would that be due to the cpu overcocking on the 7820X? In my mind, in that specific case, it makes sense that it would have a more significant impact than in more memory starved setups as there aren't as many cores to make use of all the bandwidth. That being said, maybe I should consider trying to overclock the 9800X just a tad. I'll also try to look into overclocking the 3600 memory, if possible, as you mentioned in 5. It is b-die, which I've heard is good, but I'll have to look into it further before I try anything.

Thank you for taking the time to help me out, once again! This pretty much solves it, the Ryzen setup is starting to get too many "ifs" for a lower maximum potential performance for my taste.
The 3600 would have been killer in terms of price/performance if it came any closer to the 9800X, but it hasn't been found to have great results so far, so I gotta go with what I have so far. I might as well just pay a little more and be more confident that I'll get even better results.

I'll still wait for zen 3 just in case, but I'll keep an eye out for good deals on RAM and the x299 stuff.

[ships26]

Hello again!

In my quest for buying the components, I have found a deal that's intriguing me: a used Asus ROG X299 E-Gaming + i7-7800x for 450 euros, and the components seem to be in good shape. Would you consider this a good deal?
I have seen this cpu being recommended here, but I'm not sure if it is still worth it.

[Simbelmynë]

Originally Posted by ships26

and the components seem to be in good shape.

Since you give this statement I assume that you have physical access to the setup. I suggest that you run a few benchmarks with OpenFOAM for instance to assess the performance.


The 7800X is probably starved by low core count. However, on the bright side is that you will probably see improvements when overclocking the CPU. To reach high overclocks you might need to delid the CPU and that may not be something you like to do. If you are not afraid to damage your hardware then it is well worth it if you plan on overclocking.

[flotus1]

The CPU, while not necessarily a bad choice for a budget CFD workstation, is worth less than 150€. I would not spend 300€ on a used X299 motherboard.

[ships26]

Originally Posted by Simbelmynë

Since you give this statement I assume that you have physical access to the setup. I suggest that you run a few benchmarks with OpenFOAM for instance to assess the performance.

I think I could give them a call to find a way to arrange that, but I think Flotus is right. I'd probably end up overspending for the used mobo.

Oh, I'd be up for overclocking the cpu mildly, but deliding is going a bit too far for me.

Thank you both for helping me out here again.

[ships26]

So, Zen 3 has kinda exploded into the scene. From what I have read, the memory controller is still the same, but it can go up to 3800MHz or 4000MHz when you get a good sample. It seems it was a big leap comparing to zen 2 in pretty much everything, but I don't know what to make of it for CFD.


Do you think there's a reason for me to reconsider my purchasing decisions, or am I still good because of the bandwidth provided by the quad-channel in the 9800x?


Edit: There is an interesting FEM benchmark here: https://www.techpowerup.com/review/a...-5800x/10.html. There's a good performance increase, apparently. That being said, I think I've seen this benchmark once in this forum, and I'm not sure it scales with memory bandwidth as much as most CFD codes.

[Simbelmynë]

I think 9800X is still a good value.

The Euler3D benchmark is not very representative for the common FVM codes. Also, many of the presented result just don't make sense.

Finally, looking at the other results and comparing them to other sites, it seems the reliability of the site you link is not very high, imho.

Unfortunately the entire 5000 series sold out in less than one minute in Sweden upon release. Otherwise I would have presented you with some real numbers.

The next shipment is in the beginning of December. If you cannot wait then perhaps you can lurk about on hardware forums and try to get someone to run the OpenFOAM benchmark for you.

[ships26]

Originally Posted by Simbelmynë

I think 9800X is still a good value.

For sure, I think so too! Actually, with the price increases by AMD, I'm finding it a bit more expensive to build a zen 3 machine than an x299 one right now (with 8 cores). I also believe that the 9800x probably has some more headroom for improvement with overclocking of both cpu and memory (speculating a bit here), but in case it becomes very very close between the two, the 5800x would become the better option (damn it, AMD, I wanna order the thing!).

Alas, we'll only know with numbers, and thank you for offering to provide those!

In the mean time, I'll try to ask around, as I've just ordered a motherboard I found a good deal on, but that can still be returned to the store, if need be.

As for the benchmark/website, I agree with you. It was a mistake by me, thank you for pointing it out.

[ships26]

Ok, so I've decided to go X299 after all this time.

But I have one last question: I've found a few used 10900x with warranty at about 100 euros over the 9800x (new).


I've noticed it has a better memory controller than the 9900x and the 9800x. However, I'm not sure this is worth it. What do you think? I do realize I'm stepping a bit above my original budget, though.


I can overclock the 9800x a little, and it might compensate for the 2 extra cores, but if the memory controller is better I can most likely see an improvement in performance with the 10900x.
Other than that, it's the old thing of used vs new.

[Simbelmynë]

Sorry, I'm not sure about this. For only 100 Euro (with warranty!) then the 10900X may be a better choice. I think you will be happy with either, as long as you have reasonable expectations on the performance

Make sure to get good memory and cross your fingers that the IMC of your CPU is a good one.

[ships26]

Originally Posted by Simbelmynë

I think you will be happy with either, as long as you have reasonable expectations on the performance

Thank you, I needed to hear this.
I believe the 9800X is enough for what I need and if I need to go above that, there are workstations at the uni for that.

Also, I'll post some benchmark results in the benchmarks thread. This cpu has been suggested many times here, so I'm sure it can come in handy.


Off topic: If you're still getting the 5800X, It'd be great to find out just what that alternative can do, even if I'm not getting it myself.


Once again, thank you a bunch!

[Stabum]

Originally Posted by flotus1

The CPU, while not necessarily a bad choice for a budget CFD workstation, is worth less than 150€. I would not spend 300€ on a used X299 motherboard.

It's always extremely interesting to read your comments. I'm thinking of building a "desktop workstation" based on 2017 Xeon Gold CPUs. For example, 2 Xeon Gold 6138s (20 cores each), would mean 40 cores in total, 6 channel DDR4 memory, with the possibility to use 48 GB ECC per CPU. Ok, the CPU frequency is not that high (2.0 GHZ, 3.7 GHz turbo) but the typical use would be Fluent with less than 5E6 cells.
In an international eshop each CPU is sold at 50€. The motherboard would be bought as new (Asus WS c621 Sage) at 500€. 8x12 = 92 GB DDR4 ECC 2666 MHz memory would cost around 300€. Adding a fast drive and a good PSU, it all would cost around 1100/1200€.
I would be extremely interested to hear your qualified opinion.

Thanks so much in advance!

[Stabum]

Originally Posted by Stabum

It's always extremely interesting to read your comments. I'm thinking of building a "desktop workstation" based on 2017 Xeon Gold CPUs. For example, 2 Xeon Gold 6138s (20 cores each), would mean 40 cores in total, 6 channel DDR4 memory, with the possibility to use 48 GB ECC per CPU. Ok, the CPU frequency is not that high (2.0 GHZ, 3.7 GHz turbo) but the typical use would be Fluent with less than 5E6 cells.
In an international eshop each CPU is sold at 50€. The motherboard would be bought as new (Asus WS c621 Sage) at 500€. 8x12 = 92 GB DDR4 ECC 2666 MHz memory would cost around 300€. Adding a fast drive and a good PSU, it all would cost around 1100/1200€.
I would be extremely interested to hear your qualified opinion.

Thanks so much in advance!

It would be nice if You could answer, Flotus.

thanks in advance

[flotus1]

Not sure if I can give much more input here.
These CPUs are surely a bargain at 50$ each. The cheap CPUs are offset by the expensive motherboards, but that's just how it is with these setups.
Be sure to get reg ECC memory. Unbuffered memory may or may not work, it's just not worth the risk.
And add 2 CPU coolers, a case, and a graphics card to your total cost.