Two Mass flow inlet bc convergence problem

nabidinhomessi · December 12, 2015, 11:58

HI all! I am trying to simulate heat transfer problem in a double pipe heat exchanger in which i need to calculate the pressure difference in the inner fluid.

Materials : inner fluid: user defined nano fluid
outer fluid: hot water
inner tube: copper
outer tube: insulated

Now if I choose two different mass flow rate for the two inlet the solution is having very annoying

convergence problem(reverse flow remain through out the simulation).But if i choose same mass flow rate for both the inlet solution converges .But i need to use to different mass flow rate for both the inlet

BC: Both inlet: Mass flow inlet(temp 298 and 318K)
BOth outlet : Outflow
Mesh :simple Mapped face meshing

Model: K epsilon standard and wall: standard

what might be the problem is it in mesh or in my bc or in the other physic setup.I can't get it even if i set mass flow rate for one inlet to 0.0789 and other inlet to 0.078 the residuals won't converge for at least first 800 iteration where if i choose 0.0789 for both the inlet it converges within first 200 iteration.

Plz help!!!!!

Papiya Debi ashru · December 12, 2015, 14:19

What is the difference between Bottom Boundary Layer and Benthic Boundary Layer?

nabidinhomessi · December 13, 2015, 00:07

sorry can you elaborate? I have no idea about your question I am very much a beginner!

Papiya Debi ashru · December 13, 2015, 14:25

Actually I'm also new comer.ould you please tell me how can I get proper answer through proper channel?

Hamidzoka · December 14, 2015, 00:27

hi
how do you set the outlet boundary condition?
do you impose the same pressure level for both outlets?
If yes, this may be the reason. these channels have not necessarily the same pressure levels.

does it help?

nabidinhomessi · December 14, 2015, 07:11

I set both the outlet boundary to outflow as i don't know the pressure at the outlet,actually i need to find the outlet pressure from the simulation.

December 12, 2015, 11:58	Two Mass flow inlet bc convergence problem	#1
nabidinhomessi New Member Nabid Aunjum Hossain Join Date: Nov 2015 Posts: 14 Rep Power: 10	HI all! I am trying to simulate heat transfer problem in a double pipe heat exchanger in which i need to calculate the pressure difference in the inner fluid. Materials : inner fluid: user defined nano fluid outer fluid: hot water inner tube: copper outer tube: insulated Now if I choose two different mass flow rate for the two inlet the solution is having very annoying convergence problem(reverse flow remain through out the simulation).But if i choose same mass flow rate for both the inlet solution converges .But i need to use to different mass flow rate for both the inlet BC: Both inlet: Mass flow inlet(temp 298 and 318K) BOth outlet : Outflow Mesh :simple Mapped face meshing Model: K epsilon standard and wall: standard what might be the problem is it in mesh or in my bc or in the other physic setup.I can't get it even if i set mass flow rate for one inlet to 0.0789 and other inlet to 0.078 the residuals won't converge for at least first 800 iteration where if i choose 0.0789 for both the inlet it converges within first 200 iteration. Plz help!!!!! Last edited by nabidinhomessi; December 14, 2015 at 07:20.

December 12, 2015, 14:19	Bbl	#2
Papiya Debi ashru New Member Papiya Debi Ashru Join Date: Dec 2015 Posts: 2 Rep Power: 0	What is the difference between Bottom Boundary Layer and Benthic Boundary Layer?

December 13, 2015, 14:25	Ask	#4
Papiya Debi ashru New Member Papiya Debi Ashru Join Date: Dec 2015 Posts: 2 Rep Power: 0	Actually I'm also new comer.ould you please tell me how can I get proper answer through proper channel? nabidinhomessi likes this.

December 14, 2015, 00:27		#5
Hamidzoka Senior Member Hamid Zoka Join Date: Nov 2009 Posts: 282 Rep Power: 18	hi how do you set the outlet boundary condition? do you impose the same pressure level for both outlets? If yes, this may be the reason. these channels have not necessarily the same pressure levels. does it help? nabidinhomessi likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Issues on the simulation of high-speed compressible flow within turbomachinery	dowlee	OpenFOAM Running, Solving & CFD	11	August 6, 2021 06:40
Total pressure and mass flow boundary condition at inlet	bscphil	OpenFOAM Pre-Processing	3	July 9, 2017 14:39
Mass flow inlet and pressure outlet issue	nikhil	FLUENT	5	December 11, 2013 12:30
Species mass flow inlet	lorenz	FLUENT	3	March 15, 2012 07:26
reversed flow at velocity inlet / mass flow inlet	ib	FLUENT	1	March 26, 2007 13:11

December 13, 2015, 00:07		#3
nabidinhomessi New Member Nabid Aunjum Hossain Join Date: Nov 2015 Posts: 14 Rep Power: 10	sorry can you elaborate? I have no idea about your question I am very much a beginner!

December 14, 2015, 07:11		#6
nabidinhomessi New Member Nabid Aunjum Hossain Join Date: Nov 2015 Posts: 14 Rep Power: 10	I set both the outlet boundary to outflow as i don't know the pressure at the outlet,actually i need to find the outlet pressure from the simulation.