Paraview re-adjusting scale when changing between velocity and pressure

katie_lo · May 3, 2020, 16:18

Hi everyone,

I am new to OpenFOAM and I have to use it for a final course project. I am trying to run a simulation of air flowing into a box shape that is connected to a u-shaped pipe. This is a cold flow analysis, no heat is considered.

I am using simpleFOAM as a solver because I want to include turbulence. When I run the simulation and open ParaView, I want to see the velocity and the pressure maps across the volume. When I change from one to the other and back again, the scale changes from (0 to 0.3 m/s) to (0 to 1e308 m/s)!

I close and reopen paraview to reset this issue. I want to slice the volume in half symmetrically to see what is happening on the inside of my system (I set the walls to zero velocity). I slice it in half and when I click "rescale to visible data" the scale then changes to (nan to 1e38 m/s).

Does anyone know why this might be happening? I have googled this and read lots of guides and cannot figure it out. I am really struggling with this! Thank you in advance

HPE · May 8, 2020, 06:40

- Can you visually check the content of "U" file at the latest time directory - may be the simulation resulted in these nonphysical "U" values?
- If you can't open your "U" files for some reason, you can execute `postProcess -func "minMaxComponents(U)" -latestTime` to see the minimum and maximum velocity components within your computational domain.

May 3, 2020, 16:18	Paraview re-adjusting scale when changing between velocity and pressure	#1
katie_lo New Member Katie Join Date: May 2020 Posts: 1 Rep Power: 0	Hi everyone, I am new to OpenFOAM and I have to use it for a final course project. I am trying to run a simulation of air flowing into a box shape that is connected to a u-shaped pipe. This is a cold flow analysis, no heat is considered. I am using simpleFOAM as a solver because I want to include turbulence. When I run the simulation and open ParaView, I want to see the velocity and the pressure maps across the volume. When I change from one to the other and back again, the scale changes from (0 to 0.3 m/s) to (0 to 1e308 m/s)! I close and reopen paraview to reset this issue. I want to slice the volume in half symmetrically to see what is happening on the inside of my system (I set the walls to zero velocity). I slice it in half and when I click "rescale to visible data" the scale then changes to (nan to 1e38 m/s). Does anyone know why this might be happening? I have googled this and read lots of guides and cannot figure it out. I am really struggling with this! Thank you in advance

May 8, 2020, 06:40		#2
HPE Senior Member Herpes Free Engineer Join Date: Sep 2019 Location: The Home Under The Ground with the Lost Boys Posts: 932 Rep Power: 12	- Can you visually check the content of "U" file at the latest time directory - may be the simulation resulted in these nonphysical "U" values? - If you can't open your "U" files for some reason, you can execute `postProcess -func "minMaxComponents(U)" -latestTime` to see the minimum and maximum velocity components within your computational domain. geth03 likes this. __________________ The OpenFOAM community is the biggest contributor to OpenFOAM: User guide/Wiki-1/Wiki-2/Code guide/Code Wiki/Journal Nilsson/Guerrero/Holzinger/Holzmann/Nagy/Santos/Nozaki/Jasak/Primer Governance Bugs/Features: OpenFOAM (ESI-OpenCFD-Trademark) Bugs/Features: FOAM-Extend (Wikki-FSB) Bugs: OpenFOAM.org How to create a MWE New: Forkable OpenFOAM mirror

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
outlet pressure Boundary settings -velocity streamline under ambient temp.conditions	Vishnu_bharathi	CFX	12	November 21, 2017 06:56
Neumann pressure BC and velocity field	Antech	Main CFD Forum	0	April 25, 2006 02:15
Variables Definition in CFX Solver 5.6	R P	CFX	2	October 26, 2004 02:13
Terrible Mistake In Fluid Dynamics History	Abhi	Main CFD Forum	12	July 8, 2002 09:11
what the result is negatif pressure at inlet	chong chee nan	FLUENT	0	December 29, 2001 05:13