Forum: OpenFOAM Running, Solving & CFD
August 9, 2023, 05:46
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
August 9, 2023, 03:52
|
Replies: 49
Views: 1,067
Then you changed you mesh! :D
You moved your...
Then you changed you mesh! :D
You moved your geometry and re-run snappy = you generated a new mesh, and you will need to map the results from the old mesh to the new mesh if you want to use the...
|
Forum: OpenFOAM Running, Solving & CFD
August 8, 2023, 08:37
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
August 8, 2023, 08:27
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
August 8, 2023, 07:46
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
August 8, 2023, 07:31
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
August 8, 2023, 07:02
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
August 1, 2023, 04:35
|
Replies: 49
Views: 1,067
There are 2 readers for ParaView to open an...
There are 2 readers for ParaView to open an OpenFOAM case:
The native reader from ParaView: it uses a empty file using the .foam extension to trigger the OpenFOAM reader in ParaView. You can...
|
Forum: OpenFOAM Running, Solving & CFD
July 31, 2023, 08:48
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
July 28, 2023, 05:55
|
Replies: 49
Views: 1,067
About the results you posted:
Your geometry...
About the results you posted:
Your geometry is not meshed. You are running your solver on an empty mesh (it's basically only the mesh created by blockMesh).
You end up with a 10m/s flow in a...
|
Forum: OpenFOAM Running, Solving & CFD
July 28, 2023, 05:36
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
July 28, 2023, 03:24
|
Replies: 49
Views: 1,067
Yes, the locationInMesh parameter in snappy,...
Yes, the locationInMesh parameter in snappy, which defines which part of the mesh is kept.
However, your screenshot is different from the mesh I got from the test case you uploaded in previous...
|
Forum: OpenFOAM Running, Solving & CFD
July 27, 2023, 08:11
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
July 27, 2023, 07:41
|
Replies: 49
Views: 1,067
Hello,
It's impossible to tell without...
Hello,
It's impossible to tell without knowing the details of your case. It can be pretty much anything: mesh, boundary conditions, numerical setup, or even physics itself...
Yann
|
Forum: OpenFOAM Running, Solving & CFD
July 26, 2023, 09:08
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
July 26, 2023, 08:31
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
July 25, 2023, 05:04
|
Replies: 49
Views: 1,067
|
Forum: OpenFOAM Running, Solving & CFD
July 25, 2023, 03:17
|
Replies: 49
Views: 1,067
Hello,
I cannot help if I don't know what...
Hello,
I cannot help if I don't know what you are doing :D
Are you running in serial or parallel?
Did snappy complete without error?
How do you load your case in paraView?
What are you...
|
Forum: OpenFOAM Running, Solving & CFD
July 24, 2023, 05:51
|
Replies: 49
Views: 1,067
OK, I think this is related to your features...
OK, I think this is related to your features refinement:
Reading features...
Read edgeMesh av1.obj
points : 0
edges : 0
boundingBox : (0 0 0) (0 0 0)
Refinement level according to distance...
|
Forum: OpenFOAM Running, Solving & CFD
July 24, 2023, 05:24
|
Replies: 49
Views: 1,067
Not with that few information. But you can post...
Not with that few information. But you can post the full snappy log file (or at least the beginning of the log, up to the part where you get the warning) which would be more helpful to have an idea...
|
Forum: OpenFOAM Running, Solving & CFD
July 24, 2023, 03:39
|
Replies: 49
Views: 1,067
Hello,
In the geometry section of your...
Hello,
In the geometry section of your snappyHexMeshDict, you geometry is named "av1.stl" but in the refinementSurfaces section you define refinement levels for "av1". You can either rename your...
|