|
[Sponsors] |
October 24, 2013, 11:30 |
Fluidized bed in Gambit
|
#1 |
Member
mohsen
Join Date: Sep 2013
Posts: 42
Rep Power: 12 |
Hi all
How to draw fluidized bed with the distributor consisted of a perforated plate of open area ratio 1.2% in GAMBIT ? Thanks in advance. |
|
October 25, 2013, 00:36 |
|
#2 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
do you have a sketch of what you want to draw?
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
October 25, 2013, 11:52 |
|
#3 |
Member
mohsen
Join Date: Sep 2013
Posts: 42
Rep Power: 12 |
Hi
a sketch of my geometry attached. My problem is in drawing distributor at bottom of the bed |
|
October 25, 2013, 12:45 |
|
#4 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
do you have a picture of this distributor?
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
October 25, 2013, 14:21 |
|
#5 |
Member
mohsen
Join Date: Sep 2013
Posts: 42
Rep Power: 12 |
No i don't have a picture of distributor .this geometry is in a paper and i want reproduce results of that paper .
in paper only that picture shown.And has written about the distributor : The distributor consisted of a perforated plate of open area ratio 1.2%. i don't know how to draw this geometry in gambit |
|
October 28, 2013, 00:53 |
|
#6 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
Then draw a plate, which is perforated from N holes with diameter D
The ration between cumulated hole-area (0.25.N.pi.D^2) and inital plate is given (1.2%). Ther is also the possibilty to work with porous media or something like that, but I neved used it http://www.cfd-online.com/Forums/flu...ed-plates.html
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
October 28, 2013, 02:55 |
|
#7 |
Member
mohsen
Join Date: Sep 2013
Posts: 42
Rep Power: 12 |
My geometry is 2D.how i can calculate number of holes?
|
|
October 28, 2013, 05:27 |
|
#8 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
January 30, 2015, 07:00 |
Perforted plate in 2d
|
#9 |
New Member
krishna
Join Date: Jan 2015
Posts: 1
Rep Power: 0 |
Hi could you help me here. I have also the problem like you described. did you have any solution for air distributor design inside bed. could you guide me here.
|
|
March 7, 2024, 04:09 |
Wholesale Perforated Metal Mesh Sheet
|
#10 |
New Member
wangmeihong
Join Date: Mar 2024
Posts: 1
Rep Power: 0 |
||
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
expansion of bed in fluidized bed | achy7pch | FLUENT | 4 | April 22, 2024 02:17 |
Gas-solid modeling (Fluidized Bed) | nezam.aziz@gmail.com | Fluent Multiphase | 0 | August 29, 2013 06:40 |
[ANSYS Meshing] How to create a 2D Fluidized Bed Mesh in Gambit | Musa | ANSYS Meshing & Geometry | 0 | December 30, 2011 02:02 |
Fluidized bed modeling | Kartus | CFX | 9 | June 30, 2011 04:41 |
Fluidized bed simulation VS particle tracking | windhair | CFX | 2 | June 28, 2011 21:10 |