[ICEM] Error: busy called re-entrantly

kepler123 · June 14, 2018, 07:54

It's been two days since I began using ICEM CFD to mesh an airfoil in 3 dimensions, so basically, I'm meshing a wing with a O mesh. I've watched a few videos by Simon and many others and have read quite a few posts on the same. However, when I try to do stuff myself, sometimes I come across an error dialogue box that says error: busy called re-entrantly as seen in this image.

I notice that this happens when I am working on split edge. I have no clue what the exact reason for the error is, because I can go back and do the exact same thing again with no error. My main problem (other than figuring out when this error occurs) is the fact that I cannot close this dialogue box without closing ICEM-CFD. Do any of you know how I can close this error box without having to restart the software and begin working all over again from the last saved point?

I looked it up online and there is absolutely no post with this error message on any website. So I'm either missing something very obvious or I'm doing something wrong.

P.S: Some time I can close the box with one click on the Ok button, other times I cannot. Most of the times I cannot. I can't say what the underlying reason for the error is when I can close this box, as I don't understand when the error shows in the first place.

kepler123 · June 15, 2018, 04:05

Update: When I close ICEM-CFD it gives me the option to save the file, I went ahead and did that and it works out fine, all I need to do is restart the program to get rid of this error. Not the best solution, but it's a solution.

Earlier I didn't risk saving on close as I assumed any discrepancies caused by the error would also be saved, but I was wrong.

Would still love to know what causes this error and how the dialogue could be closed, if at all.

June 14, 2018, 07:54	Error: busy called re-entrantly	#1
kepler123 Member Brandon Join Date: Jun 2018 Location: Germany Posts: 46 Rep Power: 7	It's been two days since I began using ICEM CFD to mesh an airfoil in 3 dimensions, so basically, I'm meshing a wing with a O mesh. I've watched a few videos by Simon and many others and have read quite a few posts on the same. However, when I try to do stuff myself, sometimes I come across an error dialogue box that says error: busy called re-entrantly as seen in this image. I notice that this happens when I am working on split edge. I have no clue what the exact reason for the error is, because I can go back and do the exact same thing again with no error. My main problem (other than figuring out when this error occurs) is the fact that I cannot close this dialogue box without closing ICEM-CFD. Do any of you know how I can close this error box without having to restart the software and begin working all over again from the last saved point? I looked it up online and there is absolutely no post with this error message on any website. So I'm either missing something very obvious or I'm doing something wrong. P.S: Some time I can close the box with one click on the Ok button, other times I cannot. Most of the times I cannot. I can't say what the underlying reason for the error is when I can close this box, as I don't understand when the error shows in the first place.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How is the turbulence model called in openfoam?	hz283	OpenFOAM	3	May 4, 2017 21:20
[blockMesh] Create time fileName::stripInvalid() called for invalid fileName UbuntuOne For d	tobimorak	OpenFOAM Meshing & Mesh Conversion	5	October 4, 2016 14:07
terminate called after throwing an instance of 'int'	b614910	SU2	10	July 27, 2014 22:16
understanding how turbulence models are called	romant	OpenFOAM Programming & Development	0	March 21, 2012 09:22
reconstructParMesh not working with an axisymetric case	francesco	OpenFOAM Bugs	4	May 8, 2009 05:49

June 15, 2018, 04:05		#2
kepler123 Member Brandon Join Date: Jun 2018 Location: Germany Posts: 46 Rep Power: 7	Update: When I close ICEM-CFD it gives me the option to save the file, I went ahead and did that and it works out fine, all I need to do is restart the program to get rid of this error. Not the best solution, but it's a solution. Earlier I didn't risk saving on close as I assumed any discrepancies caused by the error would also be saved, but I was wrong. Would still love to know what causes this error and how the dialogue could be closed, if at all.