[GAMBIT] Meshing in Gambit for analysis of flow past cylinders

PSYMN · February 25, 2012, 16:51

With mapped hexa blocks, the number of nodes on parallel edges must match (except where they are multiplied by a refinement factor).

For instance, if you have 10 nodes across one index, it must be the same the whole way across your model. You can't just set one particular edge to 7 nodes... that 7 must propagate.

The option to propagate distributions is for the "distribution" (the mesh law, initial spacing, etc.), the number of nodes must be propagated...

Far · March 11, 2012, 00:22

@PSYMN: Any solution to this problem (mesh refinement) for 2-D grids in ICEM

PSYMN · March 13, 2012, 08:33

@Far... It is a defect and has been reported. It should be sorted out for 14.5.

Far · March 13, 2012, 09:09

Thankyou very much for very detailed analysis about problem and your time. As I can see things are improving at rapid pace at ANSYS (especially due to Sr product manager

)

Far · March 28, 2012, 13:59

Quote:

With mapped hexa blocks, the number of nodes on parallel edges must match

I saw one of your presentations where you have explained that by deleting (permanently) the inner block of cylinder we can avoid this constraint on parallel edges.

Far · April 2, 2012, 08:49

I made the youtube tutorial on how to create mesh of circular cylinder in ICEM.
This is two part video tutorial.http://www.cfd-online.com/Forums/ans...-tutorial.html

Far · October 24, 2017, 02:27

This time i have solved this flow (Re=40) using chimera/overset mesh. And Cd comes out to be 1.518. So there is not much difference in results.

February 25, 2012, 16:51		#61
PSYMN Senior Member Simon Pereira Join Date: Mar 2009 Location: Ann Arbor, MI Posts: 2,663 Blog Entries: 1 Rep Power: 47	With mapped hexa blocks, the number of nodes on parallel edges must match (except where they are multiplied by a refinement factor). For instance, if you have 10 nodes across one index, it must be the same the whole way across your model. You can't just set one particular edge to 7 nodes... that 7 must propagate. The option to propagate distributions is for the "distribution" (the mesh law, initial spacing, etc.), the number of nodes must be propagated... lth likes this. __________________ ----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey

March 13, 2012, 08:33		#63
PSYMN Senior Member Simon Pereira Join Date: Mar 2009 Location: Ann Arbor, MI Posts: 2,663 Blog Entries: 1 Rep Power: 47	@Far... It is a defect and has been reported. It should be sorted out for 14.5. __________________ ----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey

March 13, 2012, 09:09	Thankyou	#64
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	Thankyou very much for very detailed analysis about problem and your time. As I can see things are improving at rapid pace at ANSYS (especially due to Sr product manager ) Last edited by Far; March 13, 2012 at 09:28.

April 2, 2012, 08:49		#66
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	I made the youtube tutorial on how to create mesh of circular cylinder in ICEM. This is two part video tutorial.http://www.cfd-online.com/Forums/ans...-tutorial.html Last edited by Far; April 2, 2012 at 22:23. Reason: correct link

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[ANSYS Meshing] Migrating from GAMBIT to ANSYS Meshing	David-CFD	ANSYS Meshing & Geometry	1	April 1, 2011 05:22
Flow past a sphere	Fabio	FLUENT	23	December 18, 2009 15:32
Supersonic flow past a wedge with counter flow	Mahesh Bailakanavar	FLUENT	0	February 14, 2008 00:21
incompressible free surface flow past cylinder	vineet	FLUENT	2	April 1, 2002 05:56
beginning - Flow past a square cylinders	Odenir de Almeida	Main CFD Forum	4	February 10, 1999 09:38

March 11, 2012, 00:22		#62
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	@PSYMN: Any solution to this problem (mesh refinement) for 2-D grids in ICEM