|
[Sponsors] |
September 8, 2015, 03:06 |
Centrifugal Pump analysis
|
#1 |
New Member
Prabhu Prakash
Join Date: Jul 2015
Location: Coimbatore, Tamil Nadu, India
Posts: 10
Rep Power: 11 |
Hi all,
I am doing a analysis in Centrifugal Pumps. I have done the model accordingly and followed the procedures suggested in Autodesk CF Design website. The iteration is going on solving more than 1500. But the solver is not converging. My boundary conditions are, Inlet pressure: 0 bar Outlet flow rate: 4 m^3 / hr Speed: 2880 rpm (table input: Speed - Time in seconds) 0 0 600 0.75 1500 1.5 2880 2 2880 100 No of blades 5 can you please help me in setting convergence parameters and proper input parameters. |
|
October 6, 2015, 12:47 |
Centrifugal trubomachinery
|
#2 |
New Member
AyAhSof
Join Date: Jun 2009
Posts: 8
Rep Power: 17 |
Hi Prabhu Prakash,
I read your request of september 2015. I don't know if you've solved your problem, but for me i'm aiming to begin a research work on the tip clearence of Centrifugal turbomachines and i need a file geometry of even a centrifugal pump or compressor. It will be kind from you if you can send to me the geometry file of the centrifugal pump you're using. Sincerly yours A. AYOUANI mail : aayouani@usthb.dz |
|
October 12, 2015, 11:56 |
Hi, AYOUANI
|
#3 |
New Member
Prabhu Prakash
Join Date: Jul 2015
Location: Coimbatore, Tamil Nadu, India
Posts: 10
Rep Power: 11 |
thanks for your interest. I will mail you the model. I have tried the simulation, but i am not able to match the test datas still. I will be happy if you get 80% of the accuracy.
|
|
October 16, 2015, 11:52 |
I would like to take a look at it
|
#4 |
New Member
Isaac
Join Date: Feb 2013
Posts: 27
Rep Power: 13 |
Hey dajjo, if you dont mind, Can you send me the model, my email id is coool5652@gmail.com
|
|
October 16, 2015, 13:36 |
SW Flow Simulation
|
#5 |
New Member
Prabhu Prakash
Join Date: Jul 2015
Location: Coimbatore, Tamil Nadu, India
Posts: 10
Rep Power: 11 |
hi isaac,
thanks for your interest, i am glad to give you my model. In which software will you perform the CFD analysis and in what format do you need the files. i have the files in Solid Works 2015 format. |
|
October 16, 2015, 13:38 |
|
#6 |
New Member
Isaac
Join Date: Feb 2013
Posts: 27
Rep Power: 13 |
I am using, Autodesk simulation 2012. You can give it to me in step format.
|
|
October 16, 2015, 13:44 |
CFD analysis
|
#7 |
New Member
Prabhu Prakash
Join Date: Jul 2015
Location: Coimbatore, Tamil Nadu, India
Posts: 10
Rep Power: 11 |
ok issac, i will mail you within few minutes....
Thanks for your interest |
|
Tags |
autodesk cfd, centrifugal pump., pumps |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Analysis of hemolysis in a centrifugal blood pump. | ameen@cfd | OpenFOAM Running, Solving & CFD | 1 | August 16, 2016 03:57 |
MRF analysis for centrifugal pump | Selvaa | FLUENT | 1 | February 19, 2015 08:47 |
3d centrifugal pump analysis in fluent_turbo | manuvel | FLUENT | 0 | May 4, 2012 03:54 |
CFD analysis of centrifugal pump | saurabh9978 | FLUENT | 1 | April 6, 2010 06:40 |
CFD analysis of centrifugal pump | saurabh9978 | FLUENT | 0 | March 21, 2010 13:07 |