|
[Sponsors] |
October 4, 2013, 09:55 |
Error
|
#1 |
Senior Member
Amin
Join Date: Oct 2013
Location: Germany
Posts: 397
Rep Power: 14 |
hi
what's the meaning of this error: "The CFX solver for system 'modelname' did not produce a results file" when I run the solution, I see this error: "The ANSYS CFX solver could not be started, or exited with return code 255: No results file has been created." |
|
October 7, 2013, 13:19 |
hi Dear
|
#2 |
New Member
saeed
Join Date: Feb 2013
Posts: 19
Rep Power: 13 |
maybe you have illegal copy of that software....check your software is active or not.you have to have an activate key...................G.luck
|
|
October 7, 2013, 17:44 |
|
#3 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,718
Rep Power: 143 |
This error does not imply it is pirated software. It simply means a simulation did not complete so not results file was generated. You would need to look into the details of the simulation setup to find what the error is.
|
|
October 8, 2013, 01:53 |
|
#4 |
New Member
Rameez
Join Date: May 2013
Posts: 19
Rep Power: 12 |
When this message pops out, close it, and have a closer view on the right hand section of the solver run, there you will get the exact error. Error might be due to some in appropriate boundary setting or due to output control setting. Thanks
|
|
October 8, 2013, 16:28 |
Thanks
|
#5 |
Senior Member
Amin
Join Date: Oct 2013
Location: Germany
Posts: 397
Rep Power: 14 |
Dear freinds!
thanks from you! but my software license is valid and it works correctly I checked the simulation again but it hasn't any result! |
|
October 8, 2013, 18:02 |
|
#6 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,718
Rep Power: 143 |
As I said, this error has nothing to do with licensing. You have a problem with your simulation setup. You would have to post more details about what you are doing if we are to help you.
|
|
October 9, 2013, 08:50 |
|
#7 |
Senior Member
Amin
Join Date: Oct 2013
Location: Germany
Posts: 397
Rep Power: 14 |
I'm modeling a simple 2D nozzle in CFX
geometry http://www.cfd-online.com/Forums/att...1&d=1381322772 mesh http://www.cfd-online.com/Forums/att...1&d=1381322794 setup http://www.cfd-online.com/Forums/att...1&d=1381322811 |
|
October 9, 2013, 17:39 |
|
#8 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,718
Rep Power: 143 |
We still have no idea what you are modelling - see: http://www.cfd-online.com/Wiki/Ansys...ible_answer.3F
|
|
October 13, 2013, 02:25 |
|
#9 |
Senior Member
Amin
Join Date: Oct 2013
Location: Germany
Posts: 397
Rep Power: 14 |
Dear ghorrocks!
as you said the error was due to incorrect settings in the simulation setup. I checked it and solve this error thanks for your help good luck! |
|
October 25, 2013, 08:49 |
good luck amin
|
#10 |
New Member
saeed
Join Date: Feb 2013
Posts: 19
Rep Power: 13 |
he simulate a symmetry airfoil...i think
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[swak4Foam] GroovyBC the dynamic cousin of funkySetFields that lives on the suburb of the mesh | gschaider | OpenFOAM Community Contributions | 300 | October 29, 2014 18:00 |
c++ libraries and solver compiling | vaina74 | OpenFOAM Installation | 13 | February 3, 2012 17:43 |
[OpenFOAM] Saving ParaFoam views and case | sail | ParaView | 9 | November 25, 2011 15:46 |
DecomposePar links against liblamso0 with OpenMPI | jens_klostermann | OpenFOAM Bugs | 11 | June 28, 2007 17:51 |
user defined function | cfduser | CFX | 0 | April 29, 2006 10:58 |