|
[Sponsors] |
August 26, 2011, 03:33 |
Non uniform pressure ansys in CFX.
|
#1 |
New Member
Join Date: Dec 2010
Posts: 6
Rep Power: 15 |
Dear All,
I was completed NACA rotor ansys with uniform pressure at inlet in CFX.I got results, which were almost matched with experimental data. Now i want to do same ansys with non uniform pressure at inlet. If anyone of us know about this process plz share with me and guide me for getting best results.my mailing address is sivajiganesh9@gmail.com. thank you for spending your valuable time. |
|
August 26, 2011, 04:52 |
|
#2 | |
New Member
Join Date: Dec 2010
Posts: 6
Rep Power: 15 |
Quote:
I was completed NACA rotor ansys with uniform pressure at inlet in CFX.I got results, which were almost matched with experimental data. Now i want to do same ansys with non uniform pressure at inlet. If anyone of us know about this process plz share with me and guide me for getting best results.my mailing address is sivajiganesh9@gmail.com. thank you for spending your valuable time. |
||
August 26, 2011, 06:37 |
|
#3 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,703
Rep Power: 143 |
What type of pressure distribution do you want to apply?
|
|
August 26, 2011, 06:45 |
|
#4 |
New Member
Join Date: Dec 2010
Posts: 6
Rep Power: 15 |
||
August 26, 2011, 07:02 |
|
#5 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,703
Rep Power: 143 |
If you have an expression as a function of position then you can either define a CEL expression or use a 1D or 3D interpolation function.
|
|
August 26, 2011, 07:13 |
|
#6 |
New Member
Join Date: Dec 2010
Posts: 6
Rep Power: 15 |
I dnt have any expression as a function of position, in CFX help file i read as by importing of .CSV file for running this case. I had assumed some points (Pressure values) at hub and casing BCZ i know the Static Pressure range, by plotting graph the Pressure Vs Radius its given curvature which was similar to what i want.But its not running properly after few iterations solutions stops.
|
|
August 26, 2011, 22:12 |
|
#7 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,703
Rep Power: 143 |
So is your problem that you cannot implement the varying pressure boundary, or that your model does not converge?
|
|
August 27, 2011, 00:18 |
|
#8 |
New Member
Join Date: Dec 2010
Posts: 6
Rep Power: 15 |
The profile is loading normally but its not creating any results file (i.e. .res file)
|
|
August 29, 2011, 05:36 |
|
#9 |
New Member
Join Date: Dec 2010
Posts: 6
Rep Power: 15 |
Dear Glenn, the inlet pressure profile is loading normally but its not creating any results file (i.e. .res file). I stuked with this case.
|
|
August 29, 2011, 18:42 |
|
#10 |
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,703
Rep Power: 143 |
If it does not produce a res file then either:
1) You told it not to. 2) The solver crashed 3) The solver had a problem reassembling the final results, this sometimes happens in parallel runs. If it is 1) then well, you can sort that one out. If it is 2 or 3 then you will need to post the output file (as an attachment) on the forum for us to help you. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Free jet simulation | msarkar | OpenFOAM Running, Solving & CFD | 39 | May 11, 2021 13:21 |
Compressible Flow in Ansys CFX | bcheruk | CFX | 15 | July 6, 2017 06:30 |
about reference pressure in CFX | adam2008 | CFX | 0 | May 14, 2011 22:14 |
Exporting results from CFX to ANSYS ?? | sohail ahmed | CFX | 1 | December 20, 2007 01:10 |
Hydrostatic pressure in 2-phase flow modeling (CFX4.2) | HB &DS | CFX | 0 | January 9, 2000 13:19 |