|
[Sponsors] |
June 8, 2022, 21:51 |
Terminated Converge Simulation
|
#1 |
Member
|
Hi All
I am trying to run a simulation and the simulation gets terminated after throwing this warning MPI shared memory is disabled for this build. This feature has been turned off. I have checked the inputs.in file and the flag for MPI shared is 1. What's happening and how do I debug this issue. These are the messages printed on the screen as well as in log file ************************************************** ****************************** * * * This software is Proprietary to Convergent Science Inc. (2008-2021) * * CONVERGE Release 3.1.4 * * Dec 20 2021 * * MPI Version: INTEL * * * * * * CEQ equilibrium solver is included under license agreement with * * Ithaca Combustion Enterprise LLC. * * * * Adaptive zoning chemistry solver is included under license agreement with * * Lawrence Livermore National Security, LLC. All rights reserved. * * * ************************************************** ****************************** Found the file 'stream_settings.in' at 'D:\Ramesh\Dropbox (Cambridge CARES)\CARES\WORK\MainWork\ShipSimulationModified\ HeadWindSimpleChem\stream_settings.in'. reading data from the file stream_settings.in reading stream_settings.in data from file D:\Ramesh\Dropbox (Cambridge CARES)\CARES\WORK\MainWork\ShipSimulationModified\ HeadWindSimpleChem\stream_settings.in Found the file 'inputs.in' at 'D:\Ramesh\Dropbox (Cambridge CARES)\CARES\WORK\MainWork\ShipSimulationModified\ HeadWindSimpleChem\inputs.in'. reading data from the file inputs.in reading inputs.in data from file D:\Ramesh\Dropbox (Cambridge CARES)\CARES\WORK\MainWork\ShipSimulationModified\ HeadWindSimpleChem\inputs.in WARNING: [3283] MPI shared memory is disabled for this build. This feature has been turned off. Geometry diagnosis is complete and there were no errors the final validation also doesn't show any warnings or errors but the code doesn't get executed. Any suggestions on where to start debugging . Regards |
|
June 10, 2022, 11:59 |
|
#2 |
New Member
Achyuth Rajendran
Join Date: May 2022
Location: Madison, WI, USA
Posts: 13
Rep Power: 3 |
Hi Ramesh,
A few things that you could try out: -after the 'WARNING' error was shown, were there any other statements shown before it crashed? Usually there are 'FATAL' errors that are written out before a simulation crashes. Could you post those if there were any? -if there were none, could you try activating Simulation Parameters-> Run Parameters-> Misc.-> Screen print level: More verbose ? This should write out a more detailed report in your screen output. -could you try checking the abort_trace_rank*.out files that are written out to understand more about your error? As always, feel free to reach out to our support team at support@convergecfd.com with your case setup so that we can take a deeper look at your issue. -Achyuth |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
HCCI simulation in converge | anirudh1 | CONVERGE | 4 | October 1, 2020 01:42 |
Centrifugal pump impeller simulation doesn't converge | JuanRincon | CFX | 8 | June 25, 2019 05:59 |
Looking for experts in Converge for IC engine simulation | pradeep6890 | CFD Freelancers | 0 | March 25, 2019 08:14 |
Convergence of jet flow simulation | MiraLisa | FLUENT | 0 | August 15, 2013 04:44 |
T reactor simulation - Dont converge - Help plz | Dinocrack | FLUENT | 0 | September 14, 2010 17:15 |