Prismatic layers in the current master branch

Fschhh · September 24, 2023, 09:50

Hi, I managed with some difficulty to compile the current (2023-09-24) master branch of engrid on Linux with VTK 9.2.6 and QT 5.15. I hat to make a few minor changes in the CMake and GUI code, which I pushed on https://github.com/guillaumechauvat/engrid .

In the tutorials I see online, and in the manual shipped with the code, there is "Mesh » create prismatic boundary layer" to create prismatic layers. This menu doesn't exist in the version I compiled.

Has it been replaced by something else (the boundary layer controls in the surface mesh settings?)? How is it supposed to work in this version?

klausb · May 22, 2024, 05:01

Can you provide detailed enGrid installation instructions when using VTK 9.2.6 and QT 5.15?

Fschhh · May 23, 2024, 09:36

It depends... What operating system do you use?

klausb · May 23, 2024, 09:40

I use Ubuntu 22.04

pj_design · September 5, 2024, 07:29

Were you able to install engrid on ubuntu 22.04? I have been trying to install it for quite a while now and haven't had any success. Any help is highly appreciated.

Regards from Austria, Paul

September 24, 2023, 09:50	Prismatic layers in the current master branch	#1
Fschhh New Member Guillaume Chauvat Join Date: Sep 2023 Location: Stockholm, Sweden Posts: 4 Rep Power: 3	Hi, I managed with some difficulty to compile the current (2023-09-24) master branch of engrid on Linux with VTK 9.2.6 and QT 5.15. I hat to make a few minor changes in the CMake and GUI code, which I pushed on https://github.com/guillaumechauvat/engrid . In the tutorials I see online, and in the manual shipped with the code, there is "Mesh » create prismatic boundary layer" to create prismatic layers. This menu doesn't exist in the version I compiled. Has it been replaced by something else (the boundary layer controls in the surface mesh settings?)? How is it supposed to work in this version?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] Multiple sets of layers to gain more control over distribution	MikeWorth	OpenFOAM Meshing & Mesh Conversion	1	April 19, 2021 08:20
[snappyHexMesh] Adding layers goes wrong with SnappyHexMesh	Elise	OpenFOAM Meshing & Mesh Conversion	1	April 22, 2013 02:32
[snappyHexMesh] Effect of adding layers with sHM	Nucleophobe	OpenFOAM Meshing & Mesh Conversion	4	August 20, 2012 16:45
[snappyHexMesh] Layers don't fully surround surface	EVBUCF	OpenFOAM Meshing & Mesh Conversion	14	August 20, 2012 04:31
What is the difference between current time step and current time	djing	FLUENT	4	May 1, 2012 16:18

May 22, 2024, 05:01		#2
klausb Senior Member Klaus Join Date: Mar 2009 Posts: 287 Rep Power: 23	Can you provide detailed enGrid installation instructions when using VTK 9.2.6 and QT 5.15?

May 23, 2024, 09:36		#3
Fschhh New Member Guillaume Chauvat Join Date: Sep 2023 Location: Stockholm, Sweden Posts: 4 Rep Power: 3	It depends... What operating system do you use?

May 23, 2024, 09:40		#4
klausb Senior Member Klaus Join Date: Mar 2009 Posts: 287 Rep Power: 23	I use Ubuntu 22.04

September 5, 2024, 07:29		#5
pj_design New Member Paul Jakob Join Date: Mar 2022 Posts: 5 Rep Power: 5	Were you able to install engrid on ubuntu 22.04? I have been trying to install it for quite a while now and haven't had any success. Any help is highly appreciated. Regards from Austria, Paul