|
[Sponsors] |
![]() |
![]() |
#1 |
New Member
Mohit
Join Date: Mar 2013
Posts: 7
Rep Power: 13 ![]() |
friends... i am doing simulation of "combustion of methane air in diverging micro channel" but I am not getting appropriate result. Even I am not getting flame. sometime I am facing floating problem and non positive volume problem...so pls help me that how can I solve this problem..by using fluent. and also tell me that what boundary condition i must use and use of model to solve it....is this problem relate to laminar or turbulent.??
Last edited by mohitmmb; March 8, 2013 at 14:38. |
|
![]() |
![]() |
![]() |
![]() |
#2 |
Member
farzadpourfattah
Join Date: Mar 2013
Posts: 41
Rep Power: 13 ![]() |
read Tutorial 12. Cold Flow Simulation Inside an SI Engine of Ansys Tutorial.
I think it will help you |
|
![]() |
![]() |
![]() |
![]() |
#3 | |
New Member
Mohit
Join Date: Mar 2013
Posts: 7
Rep Power: 13 ![]() |
Quote:
THANKS DEAR.....but i dont have this tutorial.... can u send it to my mail mohitmmb@gmail.com for my help...I will be thankful to you... |
||
![]() |
![]() |
![]() |
![]() |
#4 |
Member
farzadpourfattah
Join Date: Mar 2013
Posts: 41
Rep Power: 13 ![]() |
yes of course, I sent it you, I hope its be useful.
|
|
![]() |
![]() |
![]() |
![]() |
#5 |
New Member
hossam ali
Join Date: Jan 2013
Posts: 9
Rep Power: 13 ![]() |
||
![]() |
![]() |
![]() |
![]() |
#6 |
Member
farzadpourfattah
Join Date: Mar 2013
Posts: 41
Rep Power: 13 ![]() |
Ok i sent it for you,too.
![]() |
|
![]() |
![]() |
![]() |
![]() |
#7 |
New Member
Mohit
Join Date: Mar 2013
Posts: 7
Rep Power: 13 ![]() |
hi...., I read the cold flow problem.... but problem is littile bit different. I am doing simulation of combustion of ch4+ air(its species) in a divergent channel but i dont know the value of mass fravtion of ch4 and air species at inlet and outlet for a perticular equivalance ratio.....means suppose for equivalance ratio = 1 or 1.2
what will be the value of ch4, co2, c, o2, n2, h2o, etc at inlet and outlet...that is why I am not getting the exact flame and results....pls help me if possible.... |
|
![]() |
![]() |
![]() |
![]() |
#8 |
New Member
Beatrix Koln
Join Date: Mar 2013
Posts: 1
Rep Power: 0 ![]() |
||
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
A Problem of Fluent Interpreted UDF: parse error | knight | Fluent UDF and Scheme Programming | 25 | August 16, 2018 10:26 |
[Commercial meshers] Mesh conversion problem (fluent3DMeshToFoam) | Aadhavan | OpenFOAM Meshing & Mesh Conversion | 2 | March 8, 2018 01:47 |
Alias problem when starting FLUENT from command line | batch_error | FLUENT | 0 | May 24, 2012 08:20 |
Fluent PDF Combustion viscosity problem | laxwendrofzx9r | FLUENT | 0 | December 6, 2011 09:21 |
Problem in Tutorial problem of fluent | Phanindra | FLUENT | 5 | April 17, 2007 09:57 |