Changing fluent default settings

sunilpatil · November 20, 2019, 23:11

Hi All,
For most of my simulations, I will be changing a lot of fluent default parameters like pressure unit from pascal to psi, solution backup interval from 0 to 500, iterations to store to 5000, etc. How can I change these settings permanently so that every time I launch the fluent it will load with the modified setting.

I heard that there is an option to edit a fluent.bat file to change the default settings but I am unable to find the details about that.

AlexanderZ · November 20, 2019, 23:58

make a journal file with all your settings

LuckyTran · November 21, 2019, 08:42

Just in case you had any doubts. Make a journal file

sunilpatil · November 22, 2019, 03:58

Hi Tran,
thank you for your reply, if I make a journal file then how can run it automatically when fluent starts.

Regards,
Sunil

LuckyTran · November 22, 2019, 10:33

You don't need to run it automatically, although you could.

When you launch Fluent, you can set it to run your journal. Or you can manually run it it (by just typing file/read-journal), or it's just 3 button clicks in the GUI.

It's just the standard practice that everyone (that wants this level of control) has a journal file and runs it at some point.

AlexanderZ · November 25, 2019, 00:16

journal file could be run automatically, however, I don't remember how to do this

as far as I remember, some folder should be created in working directory with special name
that folder should contain your journal file with special filename extension

November 20, 2019, 23:11	Changing fluent default settings	#1
sunilpatil Senior Member sunil Join Date: Jul 2012 Location: Bangalore Posts: 179 Rep Power: 13	Hi All, For most of my simulations, I will be changing a lot of fluent default parameters like pressure unit from pascal to psi, solution backup interval from 0 to 500, iterations to store to 5000, etc. How can I change these settings permanently so that every time I launch the fluent it will load with the modified setting. I heard that there is an option to edit a fluent.bat file to change the default settings but I am unable to find the details about that. __________________ Regards, Sunil

November 20, 2019, 23:58		#2
AlexanderZ Senior Member Alexander Join Date: Apr 2013 Posts: 2,363 Rep Power: 34	make a journal file with all your settings LuckyTran likes this. __________________ best regards ****************************** press LIKE if this message was helpful

November 22, 2019, 03:58		#4
sunilpatil Senior Member sunil Join Date: Jul 2012 Location: Bangalore Posts: 179 Rep Power: 13	Hi Tran, thank you for your reply, if I make a journal file then how can run it automatically when fluent starts. Regards, Sunil __________________ Regards, Sunil

November 25, 2019, 00:16		#6
AlexanderZ Senior Member Alexander Join Date: Apr 2013 Posts: 2,363 Rep Power: 34	journal file could be run automatically, however, I don't remember how to do this as far as I remember, some folder should be created in working directory with special name that folder should contain your journal file with special filename extension __________________ best regards ****************************** press LIKE if this message was helpful

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Some settings were missing if exported from Hypermesh to Fluent	QQ1034914840	FLUENT	0	June 19, 2016 15:04
Lift and Drag pattern change wit FLUENT 16 and 13 PISO for same mesh n solver setting	arunraj	FLUENT	0	June 2, 2016 22:58
The fluent stopped and errors with "Emergency: received SIGHUP signal"	yuyuxuan	FLUENT	0	December 3, 2013 22:56
Fluent default surface boundary condition	lalupp	FLUENT	2	February 27, 2012 03:30
Changing default values	dcwnj	CFX	1	February 6, 2008 15:46

November 21, 2019, 08:42		#3
LuckyTran Senior Member Lucky Join Date: Apr 2011 Location: Orlando, FL USA Posts: 5,675 Rep Power: 66	Just in case you had any doubts. Make a journal file

November 22, 2019, 10:33		#5
LuckyTran Senior Member Lucky Join Date: Apr 2011 Location: Orlando, FL USA Posts: 5,675 Rep Power: 66	You don't need to run it automatically, although you could. When you launch Fluent, you can set it to run your journal. Or you can manually run it it (by just typing file/read-journal), or it's just 3 button clicks in the GUI. It's just the standard practice that everyone (that wants this level of control) has a journal file and runs it at some point.