CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > FLUENT

Heat transfer problem at nucleate boiling

Register Blogs Members List Search Today's Posts Mark Forums Read

Like Tree1Likes
  • 1 Post By MrStuebb

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   July 15, 2010, 18:11
Default Heat transfer problem at nucleate boiling
  #1
New Member
 
Join Date: Jul 2010
Posts: 5
Rep Power: 16
MrStuebb is on a distinguished road
Hello,

I´m trying to simulate nucleate boiling of an ammonia-water-mixture by fluent 6.3. in a pipe with turbulent flow and eulerian multiphase model. Therefor I´m using the udf of the "Nucleate Boiling"-Tutorial by Fluent. For this udf I defined two boundary conditions for the interior wall, one for the solid side (wall) and one for the fluid side (wall-shadow). The mesh on the fluid side got a very fine boundary layer.

My Problem:
The solution doesn´t show any heat transfer between wall and fluid. I´m sure that material data, entered in fluent and udf, are correct because I tried to iterate the tutorial data with original udf on my mesh in the same way the tutorial do. But no heat transfer occurs.

If there is someone with an idea for solving my problem I´m thankful for telling me.

best regards

mrstuebb
MrStuebb is offline   Reply With Quote

Old   August 13, 2010, 12:57
Default Boiling model
  #2
New Member
 
Khurram
Join Date: Aug 2010
Posts: 10
Rep Power: 16
deep_seak is on a distinguished road
Hi. I am also trying to simulate the same tutorial case and having the same problem. I even tried to model the same geometry as the tutorial's one and also import the original mesh file in gambit and then exported it again and run the solution. But in all the above cases no heat transfer occured. If you find any answer then please send me at deep_seak@yahoo.com
deep_seak is offline   Reply With Quote

Old   January 7, 2011, 12:59
Default
  #3
New Member
 
Join Date: Jul 2010
Posts: 5
Rep Power: 16
MrStuebb is on a distinguished road
Hello,

late, but better than never

try to change the wall-shadow and wall-shadow-shadow boundaries of the pipe wall with each other. When I remind correct, it was the failure in my case.
rolin212 likes this.
MrStuebb is offline   Reply With Quote

Old   February 27, 2011, 10:56
Default
  #4
New Member
 
Hamdy
Join Date: Jan 2011
Posts: 9
Rep Power: 15
hamdy is on a distinguished road
Sorry, but i have similar problem. Could you plz send me the boiling tutorial on my mail: hamdy.abotaleb@yahoo.com

Thanks
hamdy is offline   Reply With Quote

Old   May 21, 2011, 02:34
Default
  #5
New Member
 
majid sattarcheh
Join Date: Feb 2011
Posts: 4
Rep Power: 15
majidsa6 is on a distinguished road
hi my friend,

if u send for me your udf code i can help u

because i should run it in fluent and i answer to u for your error
majidsa6 is offline   Reply With Quote

Old   June 12, 2011, 23:08
Default
  #6
New Member
 
gleb
Join Date: Jan 2011
Posts: 7
Rep Power: 15
Ghalebsater is on a distinguished road
Hello guyz, Is there a UDF for 3d or the given 2d udf from the tutorials will work on any 3d model. Any idea??
Ghalebsater is offline   Reply With Quote

Old   April 4, 2012, 08:57
Default
  #7
New Member
 
raoudha
Join Date: Nov 2009
Posts: 18
Rep Power: 17
raoudha is on a distinguished road
Quote:
Originally Posted by MrStuebb View Post
Hello,

I´m trying to simulate nucleate boiling of an ammonia-water-mixture by fluent 6.3. in a pipe with turbulent flow and eulerian multiphase model. Therefor I´m using the udf of the "Nucleate Boiling"-Tutorial by Fluent. For this udf I defined two boundary conditions for the interior wall, one for the solid side (wall) and one for the fluid side (wall-shadow). The mesh on the fluid side got a very fine boundary layer.

My Problem:
The solution doesn´t show any heat transfer between wall and fluid. I´m sure that material data, entered in fluent and udf, are correct because I tried to iterate the tutorial data with original udf on my mesh in the same way the tutorial do. But no heat transfer occurs.

If there is someone with an idea for solving my problem I´m thankful for telling me.

best regards

mrstuebb
hello mrstuebb

I´m also trying to simulate two phase flow of an ammonia-water-mixture by fluent in vertical tubes, my problem is how to define the materiel properties of water-ammonia mixture, could you help pleaaaase

thank a lot
raoudha
raoudha is offline   Reply With Quote

Old   April 4, 2012, 15:18
Default
  #8
New Member
 
Join Date: Jul 2010
Posts: 5
Rep Power: 16
MrStuebb is on a distinguished road
Hi,

as far as I can remember we calculated the material properties according to the volume rates of water and ammonia in the mixture and entered it as one phase into FLUENT. In FLUENT you have the possibility to determine the material properties as a function of temperature.

The properties of vaporization of the mixture were determined in a UDF-function, related to the temperature and pressure of the mixture.

I hope I this will help you!
MrStuebb is offline   Reply With Quote

Old   April 11, 2012, 09:23
Default
  #9
New Member
 
raoudha
Join Date: Nov 2009
Posts: 18
Rep Power: 17
raoudha is on a distinguished road
thank you very much i'll try this, hope it works
best regards
raoudha is offline   Reply With Quote

Old   April 25, 2012, 13:05
Default
  #10
New Member
 
raoudha
Join Date: Nov 2009
Posts: 18
Rep Power: 17
raoudha is on a distinguished road
dear MrStuebb

i'm still trying to write the UDF for ammonia-water mixture properties, could you pleaaaaaaaaaaase help me with en example cause it's the first time i deal with UDfs and it seems a little complicated, would you help pleaaase, my mail is " garma_raoudha@yahoo.fr "

with lot of thank
raoudha is offline   Reply With Quote

Old   December 18, 2014, 15:35
Default
  #11
New Member
 
Ahmed F. AL-Neama
Join Date: Dec 2014
Posts: 1
Rep Power: 0
ahmedalneama is on a distinguished road
Sorry, but i have similar problem. Could you please send me the boiling tutorial on my mail: ahmad_alniema@yahoo.com

Thanks
ahmedalneama is offline   Reply With Quote

Old   March 27, 2016, 12:41
Default
  #12
New Member
 
jigneshrohit
Join Date: Mar 2016
Posts: 15
Rep Power: 10
jigneshrohit99 is on a distinguished road
can anyone provide me tutorial of nucleate boiling of in horizontal pipe?

can anyone tell me where to download fluent tutorials pdf and zip files?
jigneshrohit99 is offline   Reply With Quote

Old   March 14, 2017, 14:31
Default Boiling model
  #13
Rag
New Member
 
RAG
Join Date: Mar 2017
Posts: 5
Rep Power: 9
Rag is on a distinguished road
Hi guys,

I am also trying to simulate Nucleate boiling using ANSYS in a 3D model.
I am using Eulerian 2 phase flow model with RPI boiling implicit.

But while running the calculations, it is showing 'Floating point exception' error.
What it mean?
Has Any one have the tutorials?
is there any UDF should be included?

Please, Anyone here!!
I need your Help!!

Thanks in advance.
__________________
d_Rag
Rag is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
inverse heat transfer problem siva0182 FLUENT 6 February 22, 2019 07:00
BOILING HEAT TRANSFER COEFFICIENT John CFX 3 April 4, 2012 18:50
Conjugate heat transfer problem hvem10 FLUENT 2 October 29, 2009 18:31
heat transfer problem. vipin CFX 2 July 18, 2006 11:05
Boiling heat transfer calculation david CFX 0 June 21, 2005 05:17


All times are GMT -4. The time now is 12:31.