My FSI simulation (pipe-flow)

vitorspadeto · September 24, 2014, 17:24

This is my simulation using FSI. See the files in this link to download it:
http://www.filedropper.com/pipe

I used the solver inside EXTEND-BAZAAR (foam-extend) to FSI simulation. See the directory:

Screenshot from 2014-09-24 18:15:21.jpg

I used this case (3Dtube) to create my simulation. But the result was not as expected.

The deformation of the tube (due to the pressure of the pulsatile flow) should be higher. The deformation of the tube was approximately 0.01cm as should be of the order of 1cm. One could look at the files and try to find where is the error?

*I consider the fluid with viscosity of 0.0035Pa.s divided by 1050kg/m³ (density of the flow) = 0.0000033333333 m²/seconds

there in the archive( http://www.filedropper.com/pipe ) a pdf document that explains the conditions and parameters that I wanted to use in my simulation. you must read it initially. Unfortunately the compressed file you download need to change, "solid" link in the fluid/constant directory and "fluid" link in the solid/constant directory must be recreated because they became a folder in the process of .zip compression...

Best Regards,
Vitor Spadeto

vitorspadeto · September 24, 2014, 17:27

sorry for posting in this area, but I believe that in other areas of the forum no one will know answer....

September 24, 2014, 17:24	My FSI simulation (pipe-flow)	#1
vitorspadeto Member Tommy Sp Join Date: Jan 2014 Posts: 51 Rep Power: 12	This is my simulation using FSI. See the files in this link to download it: http://www.filedropper.com/pipe I used the solver inside EXTEND-BAZAAR (foam-extend) to FSI simulation. See the directory: Screenshot from 2014-09-24 18:15:21.jpg I used this case (3Dtube) to create my simulation. But the result was not as expected. The deformation of the tube (due to the pressure of the pulsatile flow) should be higher. The deformation of the tube was approximately 0.01cm as should be of the order of 1cm. One could look at the files and try to find where is the error? *I consider the fluid with viscosity of 0.0035Pa.s divided by 1050kg/m³ (density of the flow) = 0.0000033333333 m²/seconds there in the archive( http://www.filedropper.com/pipe ) a pdf document that explains the conditions and parameters that I wanted to use in my simulation. you must read it initially. Unfortunately the compressed file you download need to change, "solid" link in the fluid/constant directory and "fluid" link in the solid/constant directory must be recreated because they became a folder in the process of .zip compression... Best Regards, Vitor Spadeto

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
sonicFoam - pressure driven pipe: flow continuity violation and waveTransmissive BC	Endel	OpenFOAM Running, Solving & CFD	3	September 11, 2014 16:29
Vertical Pipe water flow	Goutam	FLUENT	0	April 30, 2014 08:25
Flow simulation in a Pelton turbine nozzle	fivos	FLUENT	0	April 19, 2011 11:46
About Turbulence Intensity (Pipe flow assimilated)	gRomK13	Main CFD Forum	1	July 10, 2009 03:11
FDTD Simulation of flow through tapered pipe	Jim	Main CFD Forum	3	December 25, 2006 10:56

September 24, 2014, 17:27		#2
vitorspadeto Member Tommy Sp Join Date: Jan 2014 Posts: 51 Rep Power: 12	sorry for posting in this area, but I believe that in other areas of the forum no one will know answer....