|
[Sponsors] |
June 26, 2009, 16:58 |
3D mesh
|
#41 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
hi Dear Niklas
what is my mistake? what is its correction? how can i describe an axi-symmetric mesh for diesel foam? I ran a 3D simulation of dieselfoam with last characteristic of n-heptane experiment and add its result to a new plot and attached it. there are two strange things: 1- I saw some fluctuations in liquid penetration curve in 3D cases. 2- likewise liquid penetration is far from experimental result. what is the reason of these? I set the initial drop diameter to nozzle diameter according to injector model.is it correct? I am confused. Please help me. thanks regard Last edited by az1362f; June 27, 2009 at 11:31. |
|
June 27, 2009, 13:35 |
axi-symmetric Mesh
|
#42 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi
I tried to solve last problem that I discussed in my last posts by axi-symmetric mesh but my results likewise were incorrect and far from experimental result. I attached axi-symmetric Mesh. please check my axi-symmetric blockmesh. is it correct? I tried to 3D simulation of dieselfoam of n-heptane experiment but results were far from experiment and had fluctuations. Why are my result far from experiment? please help me. Thanks regard |
|
June 29, 2009, 11:29 |
axi-symmetric Mesh
|
#43 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dr Niklas
I tried to solve last problem that I discussed in my last posts by axi-symmetric mesh but my results likewise were incorrect and far from experimental result. I attached axi-symmetric Mesh. please check my axi-symmetric blockmesh. is it correct? I tried to 3D simulation of dieselfoam of n-heptane experiment but results were far from experiment and had fluctuations. Why are my result far from experiment? please help me. Thanks regard |
|
June 30, 2009, 03:11 |
mesh dependency
|
#44 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dr Niklas;
I tried to solve axi-symmetric dieselfoam for n-heptane fuel,and when I compare my result by experimental result I couldn't find a mesh size of dependency. I attached my axi-symmetric mesh in last posts and new plot of liquid penetration: Is my axi-symmetric mesh correct? if yes why liquid penetration increased as mesh size is refined? Thanks Regard |
|
June 30, 2009, 04:39 |
|
#45 | |
Super Moderator
Niklas Nordin
Join Date: Mar 2009
Location: Stockholm, Sweden
Posts: 693
Rep Power: 29 |
Quote:
in general liquid penetration increase if you refine the mesh, thats because you resolve the jet better and hence reduce the relative velocity. You also have to investigate the influence on initial turbulent length scale, which also is very important. reducing the length scale will also increase the liquid penetration. there are no ways around these problems for lagrangian/eulerian simulations. you just have to live with the grid dependency. |
||
July 1, 2009, 12:45 |
Validating spray
|
#46 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dear Niklas;
then what is the way to validate spray simulation problem,when you don't know is your solution independent of mesh? regard |
|
July 4, 2009, 11:55 |
interpolation scheme
|
#47 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dear Niklas;
Which interpolation scheme did you use for Inter-Phase Coupling in dieselfoam code? Where can I see its implementation in dieselfoam code? I attached two method of Inter-Phase Coupling,which one did you use in dieselfoam? Thanks Regard |
|
July 6, 2009, 03:44 |
|
#48 |
Super Moderator
Niklas Nordin
Join Date: Mar 2009
Location: Stockholm, Sweden
Posts: 693
Rep Power: 29 |
||
July 7, 2009, 06:22 |
|
#49 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dear NIklas;
Which of interpolation scheme did you used in dieselfoam? equation 116 or equation 117: if 117 how is it for Hexahedron cell? thanks |
|
July 8, 2009, 02:08 |
|
#50 |
Super Moderator
Niklas Nordin
Join Date: Mar 2009
Location: Stockholm, Sweden
Posts: 693
Rep Power: 29 |
in foam its always 117.
The cell is always split into a tet containing the parcel. if you use cellPoint, it will use the nodes and cell-center to construct the tet. if you use cellPointFace it will use the nodes, cell center and face center to construct the tet. |
|
July 9, 2009, 10:44 |
implementation
|
#51 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dear Niklas;
I am very thankful for your very good and complete answers. I have a question about where is the implementation of eq.117 in Foam? also,I studied your article by subject of "Numerical Investigation of Mesh/Turbulence/Spray Interaction for Diesel applications",you talked in this article about limiting turbulenc lengh scale, is it limited in openfoam 1.5 for dieselfoam? if no, where can i limit it? Thanks Regard Last edited by az1362f; July 11, 2009 at 17:34. Reason: adding new question |
|
July 11, 2009, 17:44 |
turbulent length scale
|
#52 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dear Niklas;
I am very thankful for your very good and complete answers. I have a question about where is the implementation of eq.117 in Foam? also,I studied your article by subject of "Numerical Investigation of Mesh/Turbulence/Spray Interaction for Diesel applications",you talked in this article about limiting turbulenc length scale, is it limited in openfoam 1.5 for dieselfoam? if no, where can i limit it in the code according your article? Thanks Regard |
|
July 13, 2009, 11:09 |
turbulence length scale
|
#53 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi Dear Niklas;
I am very thankful for your very good and complete answers. I have a question about where is the implementation of eq.117 in Foam? also,I studied your article by subject of "Numerical Investigation of Mesh/Turbulence/Spray Interaction for Diesel applications",you talked in this article about limiting turbulence length scale, is it limited in openfoam 1.5 for dieselfoam? if no, where can i limit it in the code according your article? Thanks Regard |
|
July 20, 2009, 04:51 |
finding parcel
|
#54 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hi to all,
any body knows how openfoam check the existence of particle in an eulerian cell? in the other word which function or class find if there is a parcel in the current cell? |
|
July 22, 2009, 12:51 |
limiter
|
#55 |
Member
amin
Join Date: May 2009
Posts: 62
Rep Power: 16 |
Hello Dear Dr Nordin;
I saw in RASProperties file that for K-epsilon model there are two parameters for limiter :" muLimiter on;Lsgs 0.0002; are these parameters activate turbulent length scale limiter in openFoam version 1.5? please answer me. thanks regard |
|
September 28, 2009, 11:32 |
|
#57 |
Member
Christof Benz
Join Date: Mar 2009
Posts: 52
Rep Power: 17 |
Hi,
i use octave/matlab to calculate penetration length. the position of the parcel you can find in $FOAM_CASE/timeDirectory/lagrangian/defaultCloude/position. The liquid is defined in $FOAM_CASE/thermophysicalProperites Christof |
|
October 1, 2009, 06:23 |
|
#58 | |
New Member
HuangWei
Join Date: Mar 2009
Posts: 8
Rep Power: 17 |
Quote:
i have found the "position" file ,but i want to know how to calculate penetration length.Thank you very much,Christof huoyinghw |
||
October 26, 2011, 04:12 |
|
#59 | |
New Member
Join Date: Jan 2011
Posts: 9
Rep Power: 15 |
Quote:
Hello Amin, how did you implement this function can you share it, i m having this problem to implement in dieselFoam |
||
June 12, 2012, 22:42 |
|
#60 |
Member
Join Date: Jun 2012
Posts: 65
Rep Power: 13 |
hi dude,I confront a problem similar to yours now, where should I go to for changing the chem.inp and therm.dat files?
|
|
Thread Tools | Search this Thread |
Display Modes | |
|
|