|
[Sponsors] |
March 27, 2009, 21:34 |
where is the superman ---about the IPSA-full
|
#1 |
New Member
paul zhang
Join Date: Mar 2009
Posts: 8
Rep Power: 17 |
dear all:
i want to simulate the two-flow fluid with IPSA-full model .but (1)how can i get the value of P2,and how can i modify the P2 value .for example make p2=p2+constant (2)in the IPSA-full model ,how does it trace the interface of two-flow.could you tell me where the associated subroutine is |
|
April 9, 2009, 21:14 |
|
#2 |
New Member
paul zhang
Join Date: Mar 2009
Posts: 8
Rep Power: 17 |
no one???/?/???/
|
|
April 27, 2009, 07:57 |
P2 in IPSA
|
#3 |
Member
michael malin
Join Date: Mar 2009
Location: london
Posts: 33
Rep Power: 18 |
If you enter STORE(P2) in the Q1 input file , then PHOENICS will compute the pressure acting on the 2nd-phase momentum momentum to be P1 + P2, where P1 is the pressure acting on phase 1. Therefore, P2 is the EXTRA pressure experienced by phase 2.
It is the responsibility of the user to specify the formula for P2 in Group 19 Section of GROUND, or alternatively by use of the INFORM facility within the Q1 input file. A GROUND-coding example of setting a P2-formula is given in Group 19 Section 4 of the file GREX3.FOR, as follows: C IF(STORE(P2)) THEN IF(STORE(VPOR)) THEN C.... Extra second-phase pressure proportional to volume fraction C divided by porosity. CALL FN15(P2,R2,VPOR,0.0,PHS2PA) ELSE IF(PHS2P) THEN C.... Extra second-phase pressure proportional to: C a*(r2-r2crit)**b if r2 gt r2crit. L0R2=L0F(R2) L0P2=L0F(P2) RLX=ABS(DTFALS(P2)) DO 1941 I=1,NXNY IF(F(L0R2+I).GT.PHS2PA) THEN GP2=PHS2PB*(F(L0R2+I)-PHS2PA)**PHS2PC ELSE GP2=0.0 ENDIF F(L0P2+I)=RLX*GP2+(1.0-RLX)*F(L0P2+I) 1941 CONTINUE ELSE C.... Extra second-phase pressure proportional to volume fraction CALL FN2(P2,R2,0.0,PHS2PA) ENDIF ENDIF ENDIF ENDIF |
|
April 28, 2009, 03:04 |
|
#4 |
New Member
paul zhang
Join Date: Mar 2009
Posts: 8
Rep Power: 17 |
Thanks for phoenics_cfd's immediately reply
now if i want to specify my EXTRA pressure experienced by phase 2,is it correct to specify the formula for P2 in Group 19 Section 4? is it neceesary for me to change the pressure correction methods? and how could i change the P2 by use of the INFORM ? THANK YOU AGAIN |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rotor 67 full compressor geometry | jf | Main CFD Forum | 3 | January 28, 2024 05:14 |
full multicomp DIFF? | jdb | FLUENT | 0 | May 11, 2005 21:58 |
Full Buoyancy model | Swapnil | CFX | 2 | April 30, 2003 08:54 |
Full System Solution Provider? | Donald Casteel | Main CFD Forum | 0 | April 13, 2003 12:44 |
How to model a full 3-D cylinder in cfx44? | S. Ding | CFX | 1 | June 26, 2002 11:32 |